Barco F(L)35 Command Reference Manual page 13

MFBX Factory Measured Blue X
Factory Measured Blue Y
MFBY
MFBL Factory Measured Blue
Luminance
Factory Measured White X
MFWX
MFWY Factory Measured White Y
Factory Measured White
MFWL
Luminance
Factory Measured BC1 X
MFDX
Factory Measured BC1 Y
MFDY
Factory Measured BC1
MFDL
Luminance
MFEX Factory Measured BC2 X
Factory Measured BC2 Y
MFEY
MFEL Factory Measured BC2
Luminance
Color Management Test Patterns
CMTP
Picture->Advanced->Source Correction
IBCO Individual brightness and contrast
offset adjustments
Brightness offset red
BOR0
BOG0 Brightness offset green
Brightness offset blue
BOB0
COR0 Contrast offset red
Contrast offset green
COG0
Contrast offset blue
COB0
Installation
DESK Select orientation - Desktop Front
Select orientation - Ceiling Front
CEIL
RDES Select orientation - Desktop Rear
Select orientation - Ceiling Rear
RCEI
ORIE Select orientation - Absolute
value
Source Scan
SCAN
IR01 IR Enable 1
IR Enable 2
IR02
IR03 IR Enable 3
OSD Enable
OSDC
Test Image
TEST
Dual Head Setup Mode
DHED
Sync termination VGA
SVGA
SNCL Sync level VGA
Sync Level SOG
SNCS
OPFI Infitec filter
Infitec CSC
CSCC
EDIR Edit resolution
Edid type
EDIT
601-0381-00_GP3/GP4
Sicilium_1_24
GP3, GP4 Get, Set Manufacturing
GP3, GP4 Manufacturing
Get, Set
GP3, GP4 Get, Set Manufacturing
GP3, GP4 Manufacturing
Get, Set
GP3, GP4 Get, Set Manufacturing
GP3, GP4 Manufacturing
Get, Set
GP3 Manufacturing
Get, Set
GP3 Manufacturing
Get, Set
GP3 Manufacturing
Get, Set
GP3 Get, Set Manufacturing
GP3 Manufacturing
Get, Set
GP3 Get, Set Manufacturing
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3 Get, Set End User
GP3, GP4 End User
Get, Set
GP3, GP4 End User
Get, Set
GP3, GP4 End User
Get, Set
GP3, GP4 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
GP3 Get, Set End User
GP3 End User
Get, Set
GP3, GP4 Get, Set End User
GP3, GP4 End User
Get, Set
3. ASCII Command Sets
0 - disable, 1 - enable 0-RGB, 1-IR
(if available)
See value table ORIE
0 - disable, 1 - enable
0 - disable, 1 - enable
0 - disable, 1 - enable
0 - disable, 1 - enable
See value table OSDC
0 - 7 different test patterns
0 - off, 1 - side by side
0 - 2.2kOhm, 1 - 75Ohm
0-255
0-31 Infitec only
0 - disable, 1 - enable Infitec only
0 - disable, 1 - enable
See value table EDIR
See value table EDIT
10