Barco F35 Quick Start Manual

1
ge tt i n g s t a r te d
This Quick Start Guide has been design to aid in quickly getting started with using your new projector. If you require further help, or have further questions on the
detail in how to operate this unit, please refer to the user guide or our web site. You can also access FAQs, and download detailed white papers in order to get to
know the more specific product features and benefits.
Packaging contents:
projector unit
remote control
2
m o u n t p r o j e c t i o n l e ns , g e t t o k n ow t h e c on n ec t or p an el
Carefully mount the projection lens. Remove protection end caps on lens and bayonet mount, then insert, and turn clockwise until it stops and a click sounds. The
connector panel at the back features a wide range of connectors for all sorts of source connections. Decide which one(s) that meet(s) your requirement(s).
3
c o n n e c t so urce s , co nn ect p owe r, p ow er on
Make sure the projector is switched off, and not connected to power when connecting to sources. Connect video and computer sources, then insert the power
cable. Power up sources, including computers and video playback devices. Power up the projector by pressing the power key (
will indicate it is in operation. CAUTION! Connecting sources to a powered projector may result in product failure. It is recommended that the power cable connector
(projector-end) or the mains power socket are accessible whilst the product is in use to enable mains power to be disconnected or switched off when connecting
source devices. This should be considered during product installation.
user documentation
power cable
). A steady, bright indicator light
P le as e v is it ou r w e b si t e t o d ow n l oad f u l l u s er m a nua l o r f i nd re l a te d i nf or m at i o n
4
a dj ust pr oj ec to r se t ti ngs
Adjust zoom to set correct image size, shift to position correctly, focus for clarity, and any other desired setting, such as tilt or keystone. Note that keystone is very
rarely needed when using lens shift for positioning. Adjust image level with the front feet, and tilt with the rear foot.
*
A
C
B
A: Zoom B: Focus C: Shift Press to activate. Adjust with arrow keys.
5
a dj us t i ma ge a nd sys te m se t ti ngs
Change and adjust settings such as brightness and contrast, ceiling mount and rear projection display, as well as colour calibration, and other system settings by
using the remote control or through the menu system that is accessible from the on-board keypad.
6
powe r of f a nd al l ow to c oo l down
To power off, press the power ( ) key once, and confirm by pressing again. Allow to cool down (a minimum of 30 seconds) until steady amber indicator lights
indicate that the projector has been safely turned off. Disconnect any cables, sources and power cables before uninstalling the projector.
* Pictures show backpanel of projector with UHP lamps.
*
LED illumination projectors have one indicator lamp (LED), instead of two (LAMP 1, LAMP 2).
** 3D menu feature only appliable for Active Stereo 3D-enabled projectors.
The cabinet colour may differ from the one shown in the pictures.
When referring to the term F35/FL35 in this document, it means that the content is applicable
for the following Barco products:
• F35 1080p FL35 1080p
• F35 WUXGA FL35 WUXGA FS35 IR WUXGA + Addendum
• F35 WQXGA FL35 WQXGA FS35 IR WQXGA + Addendum
• F35 Panorama (2560x1080)
Quick Start Guide
D
E
D: Lens shift (operated from back) E: Lens
release button. Press in and twist lens off
stereo picture installation settings profiles
>30 s
F35/FL35
F
F: Adjustable feet for levelling
**
language status
*
www.barco.com