Optional Programming Port - Mitsubishi Electric MELSEC FX Series User Manual

FX communication

11. Optional Programming Port

This section describes connection to peripheral equipment (programming tool, data access unit
and electronic operation terminal) using the FX
232ADP , FX
1N
procedure of each peripheral equipment and installation of each interface, refer to the
corresponding manual.
11.1 FX -422-BD, FX
2N
When an FX
2N
FX or FX Series, the following peripheral equipment (programming tool, data access unit and
1N 1S
electronic operation terminal) can be connected.
However, the FX
and the FX -422-BD consumes 5V DC, 60 mA from the FX
1N
Make sure that the current consumption of 5V DC for special extensions and peripheral
equipment does not exceed the capacity of the 5V DC power of the FX
Product
FX-20P-E
FX-10P-E
Personal computer
(For programming tool)
FX-10DM
FX-10DU-E
FX-20DU-E
FX-25DU-E, FX-30DU-E,
FX-40DU-ES, FX-40DU-TK-ES,
FX-50DU-TK(S)-E
F940GOT-SWD (LWD)-E,
F930GOT-SBD
F940GOT-SBD (LBD)-H
GOT-A900 (Connecting direct
CPU port type)
*1: When using other products or cables please check the product manual for required 5V DC
supply.
Note;
These products cannot be connected via FX-2PIF to port of FX
connecting, power supply circuit in PLC will go down.
-422-BD, or FX -422-BD as well as cautions on communication. For the operating
2N
-422-BD
1N
-422-BD is installed on the FX
-422-BD consumes 5V DC, 60 mA from the FX
2N
FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP
F -232CAB-1 + FX-232AW(C) + (FX-422CAB0 or
2
FX-422CAB + FX-20P-CADP) *1
FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP
FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP
FX-20DU-CAB0 or FX-20DU-CAB + FX-20P-CADP
FX-50DU-CAB0 (-1M, -10M, -20M, -30M, L)
or FX-40DU-CAB (-10M, -20M, -30M) + FX-20P-
CADP
FX-50DU-CAB0 (-1M, -10M, -20M, -30M, L)
F9GT-HCAB2-150 + F9GT-HCAB-3M (-10M)
or FX-50DU-CAB0 (-1M) + F9GT-HCNB + F9GT-
HCAB-3M (-10M)
F9GT-CAB0 (-150, -10M)
Optional programming port 11
-232-BD, FX -232-BD, FX
2N 1N
Series, or when an FX
2N
2N
or FX
1S 1N
Connecting cable
-422-BD or FX
1N
-232ADP , FX
0N 2NC
-422-BD is installed on
1N
programmable controller,
programmable controller.
, FX or FX .
2N 1N 1S
Required 5V DC
180mA
120mA
220mA
220mA
220mA
180mA
0mA
0mA
0mA
0mA
-422-BD. If
2N
11-1
-
11