Table of Contents
Related Manuals for BIRO 922
Summary of Contents for BIRO 922
- Page 1 MODEL 922 GRINDER PARTS LIST GENERAL INSTRUCTIONS Starting with Serial Number C9861001 IMPORTANT SAFETY NOTICE This Manual contains important safety instructions which must be strictly followed when using this equipment. C957-213 213-3-04-12...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page NOTICE TO OWNERS AND OPERATORS ......... 1 SAFETY TIPS . -
Page 3: Notice To Owners And Operators
Manual. Warnings related to your personal safety are indicated by: Warnings related to possible damage are indicated by: BIRO also has provided warning labels on the equipment. If any warning label or Manual be- comes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement. -
Page 4: Safety Tips
NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Parts Missing. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning or Servicing. USE ONLY BIRO Parts and Accessories Properly Installed. -
Page 5: Installation
UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first. -
Page 6: Motor Wiring And Electrical Requirements
10. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 11. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine. -
Page 7: Electrical Contactors
(1) All 1 HP motors are dual voltage and can be changed according to wiring diagram on motor nameplate. (2) Be sure Contactor voltage matches voltage of motor. A. Item No. C903-922 Contactor B. Item No. C903-1-922 Contactor 1HP, 104-60-1... - Page 8 WIRING DIAGRAMS...
-
Page 9: Operation
OPERATION ROTATING GRINDING WORM TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Wear Gloves While Operating. DO NOT Tamper With, Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. -
Page 10: Cleaning
NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other Electrical Components. ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE BIRO MODEL 922 GRINDER 1. Disconnect grinder from power source and perform lockout/tagout procedures. 2. Remove the feed tray. -
Page 11: Maintenance
USE ONLY GENUINE BIRO Parts and Accessories Properly Installed. A. HIGH TORQUE DRIVE SYSTEM The Model 922 is driven by a High Torque Drive system for power transmissions. “No Lubrication” is required (in fact) be sure no lubricant comes in contact with the sprockets or belt. -
Page 12: Tray And Case Parts Diagram
TRAY AND CASE PARTS... -
Page 13: Tray And Case Parts List And Parts Ordering
TRAY AND CASE PARTS LIST NOTE: SPECIFY MODEL & SERIAL NUMBER WITH ORDERING PARTS C611-1 Rubber Grommet C627-1 Voltage wiring (decal) C645 Cord for 3 Phase, 14/4 SO C645-1 Cord for 1 Phase, 14/3 SO -18 ´ C649 Case to base screw, C906-1 Stomper C906-1-SLD... -
Page 14: Bowl, Frame And Motor Parts Diagram
Motor key, C664-1 C931 Worm drive shaft Shaft spacer, C670 C950 Contactor, 110 Volt End clip for din rail C903-922 C981 Contactor, 220 Volt Din rail C903-1-922 C981-1 Transformer, 380/415 Volt only Hex nut, -18, (top of motor stud) C904 H370 ´... -
Page 15: Operator's Signature Page
OPERATOR’S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SE- RIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE... -
Page 16: Limited Warranty
The warranty card must be returned to The Biro Manufacturing Com- pany for proper registration. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was originally shipped from the factory.