1. Manuals
  2. Brands
  3. BIRO Manuals
  4. Grinder
  5. Mini-32
  6. Operating and service manual

BIRO Mini-32 Operating And Service Manual

Automatic feed mixer grinder
Hide thumbs Also See for Mini-32:
Table of Contents

Advertisement

Quick Links

PTCT
MINI-32
299-7-05-2

Advertisement

Table of Contents
loading

Related Manuals for BIRO Mini-32

Summary of Contents for BIRO Mini-32

  • Page 1 PTCT MINI-32 299-7-05-2...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Page SAFETY INSTRUCTIONS ............1 SAFETY INSTRUCTIONS .
  • Page 4 — OPERATOR'S NOTES —...

  • Page 5: Safety Instructions

    No one should use or service this machine without proper training and supervision. All opera- tors should be thoroughly familiar with the procedures contained in this Manual. Even so, BIRO cannot anticipate every circumstance or environment in which its products will be used. You, the owner and operator, must remain alert to the hazards posed by the function of this equipment —...

  • Page 6: Safety Instructions

    NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Missing Parts. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning, or Servicing. USE ONLY BIRO Parts and Accessories Properly Installed.

  • Page 7: Installation

    UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first.

  • Page 8: Motor Wiring And Electrical Requirements

    8. The size of the electrical wiring required from the power source to the mixer-grinder/chopper is a MINIMUM OF No. 12 WIRE. 9. The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD...

  • Page 9: Pre-Operation

    15. Check placement of all warning labels and be sure anyone who is to operate this MINI-32 MIXER GRINDER has read and fully understands the operators manual. Machine is now ready for trained operators to process product.

  • Page 10: Parts Location

    PARTS LOCATION...

  • Page 11: Operation

    OPERATION ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Wear Gloves While Operating. DO NOT Tamper With, Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition.

  • Page 12: Cleaning

    NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other Electrical Components. ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE MINI-32 MIXER GRINDER 1. Disconnect mixer grinder from power source and/or perform lockout/tagout procedures. 2. Remove end ring, breaker plate, knife and grinding auger.

  • Page 13: Disassembly Instructions

    DISASSEMBLY INSTRUCTIONS PADDLE REMOVAL: Remove mixing paddle by first locating and lifting up on the hopper lock down clamps releas- ing them from the hopper. Next loosen the paddle lock knob (black knob located at the front of the hopper). Then turn the locking lever clockwise approximately ¼ turn and remove to unlock the paddle shaft from the hopper.

  • Page 14: Maintenance & Lubrication

    NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. USE ONLY GENUINE BIRO Parts and accessories Properly Installed. LUBRICATION 1. MOTOR: The grinder motor has pre-lubricated motor bearings. These bearings should be re-lubricated annually with a good grade of bearing grease.
  • Page 15 MOTOR DRIVE COVER HOPPER COVER Fig. Item No. Description Fig. Item No. Description -16 ´ 2, SS 50024 Auger drive shaft seal HHS086S Hex head screw Flat washer .397 ´ 1¼ ´ .120 TH, SS 63021 Nylon bearing cover EMG92032 63085 Hood, motor &...
  • Page 16 Fig. Item No. Description Fig. Item No. Description 15026-02 Double roller chain 49" 63047 Timing pulley 48H100SK 15029 Double chain master link 63048-01 Taper lock SK 1" 20050-10 #40 Roller chain 63049 Timing belt 20050-01 #40 Chain master link #40-C/L 63055 Cart assembly w/casters 53568...
  • Page 17 TRANSMISSION MOUNTING ASSEMBLY Fig. Item No. Description Fig. Item No. Description Key ¼ ´ ¼ ´ 1 20665 63081-01 Bowl support bracket – LH Key ¼ ´ ¼ ´ 1¾ SS 20665-01 63081-02 Bowl support bracket – RH 30315 O-Ring 1.25 I.D. 63084 Hopper latch rod 50029...
  • Page 18 BOWL & WORM ASSEMBLY Fig. Item No. Description 63017 Bowl mounting stud, 2 required 54278-CTN Auger assembly HK48 Knife drive pin 54278B Square drive insert 54278C Auger shear pin 54278D Shear pin screws 56049 Bowl & plate pins WN20S Wing nut -16 ´...

  • Page 19: Fasteners And Locations

    FASTENERS & LOCATIONS Base Plate (63005) to Cart Assembly (63055) Motor (63099) to Shaft Bearing Retainer-rear -16 ´ 2¼ 4 ea. HHS088S (63008) 4 ea. LW25S heavy -18 ´ 1 4 ea. HHS060S 4 ea. HN25S -16 heavy (with loctite) 4 ea.

  • Page 20: Electrical Schematic

    MINI-32 SCHEMATIC for 208-230/460 Volts, Three Phase, 60 Cycle with Elobau Magnetic Safety Switches...

  • Page 21: Foot Switch Diagrams

    OPTIONAL PNEUMATIC FOOTSWITCH...

  • Page 22: Safety Label Locations

    SAFETY LABEL LOCATIONS...

  • Page 23: Operator Signature Page

    OPERATOR’S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE...

  • Page 24: Limited Warranty

    BIRO will replace defective parts, which are covered by this limited warranty, provided that the de- fective parts are authorized for return, shipping charges prepaid, to a designated factory for in- spection and/or testing.

Table of Contents