Related Manuals for BIRO MINI-22
Summary of Contents for BIRO MINI-22
- Page 1 MODEL MINI-22 Automatic Feed Mixer Grinder Operating Manual and Parts List IMPORTANT NOTICE This Manual contains important safety instructions which must be strictly followed when using this equipment. MINI-22-374...
-
Page 3: Table Of Contents
TABLE OF CONTENTS: PAGE NOTICE TO OWNERS AND OPERATORS ........SAFETY TIPS . -
Page 4: Notice To Owners And Operators
No one should use or service this machine without proper training and supervision. All operators should be thoroughly familiar with the procedures contained in this Manual. Even so, BIRO cannot anticipate every circumstance or environment in which its products will be used. You, the owner and operator, must remain alert... -
Page 5: Safety Tips
NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Missing Parts. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning, or Servicing. USE ONLY BIRO Parts and Accessories Properly Installed. -
Page 6: Installation
1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first. 2. Remove all banding, shipping carton, and all equipment from inside the tub. Then take machine off shipping pallet. -
Page 7: Motor Wiring And Electrical Requirements
The size of the electrical wiring required from the power source to the Three phase mixer-grinder/chopper is a MINIMUM OF No. 12 GAUGE WIRE. 8. The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation. PRE-OPERATION AND AUGER ROTATION CHECK... -
Page 8: Operator's Notes
5. Check placement of all warning labels and be sure anyone who is to operate this MINI-22 MIXER GRINDER has read and fully understands the operators manual. Machine is now ready for trained operators to process product. -
Page 9: Parts Identification
PARTS LOCATION 64038 64040 Rear Cover Panel Hopper Cover (NOT SHOWN) 64037 Hood Assembly 64009 Hopper Assembly 53852 Controls Paddle Lock see page 7 Arm Assembly 64001 Grinder Bowl 56300J-CPB 64048 Female Spurt Guard coupling metal type CR22S Bowl Ring Single phase 241-3-10 A64041... - Page 10 Mini-22 Controls 42MC-Y73 Mix Start Button Hand/Foot Selector Switch Phase Specific 64029 (Single Ph) 42MC-Y74 Hand/Foot Stop Button Selector Switch EMG90668 (Three Ph) Hand/Foot Selector Switch 42MC-Y73 Grind Start Button 64026 Lid Limit Switch Located Inside Hood Assembly Upper Left Side...
- Page 11 Mini-22 Single Phase H653-SP Warning Label 64022 Spanish Side Panel Cover Single Phase Only H653-E Warning Label English BES16971 Risk of Electrical 64023 64024 Shock Grinder Variable Mixer Variable Frequency Drive Frequency Drive VTS622 (Used up to s/n: 73113) (Used up to s/n: 73113)
- Page 12 Mini-22 Three Phase H653-SP Warning Label Spanish H653-E Warning Label English BES16971 Risk of Electrical Shock 64046 Side Panel Cover Three Phase Only 64028 Mixer Motor, 1HP 64050 V-Seal 64042 Mixer Drive Shaft Coupling EMG90668 Hand/Foot Selector Switch See page 7...
- Page 13 63073-2 64040 Curved Mixing Hopper cover Paddle 63136 Paddle Spacer 64009 Hopper 63073 Round Mixing Paddle 53783 Decal, Rotation HHSM015S Hex Head Screw 3- Req’d 64013 64014 Retaining Ring 53852 Auger Drive Seal Lock Arm Bushing A64002 Auger Assembly Complete CK22 Knife Drive Pin...
- Page 14 64048 Spurt Guard 64048-1 Spurt Guard, 53783 Thumb Screw Decal, Rotation HNM46S Hex Nut 2- Required Uses 19mm Wrench 64001 Grinder Bowl CP22 Bowl Pin CR22S Bowl Ring Note- Hand tighten only 64036 19mm Wrench For Bowl Fasteners...
-
Page 15: Optional Pneumatic Foot Switch Identification
OPTIONAL PNEUMATIC FOOT SWITCH COMPLETE 56304 PNEUMATIC FOOT SWITCH COMPONENTS Part No. DESCRIPTIONS Foot Switch Assembly Complete 56304 56300BEL Bellow, Replacement 56300C Guard Only 56300K-CPB CPB Coupling Metal Body-Male 56303 Foot Switch w/Male Coupling ⅜ HHS004S Hex Head Screw, #8 - 32 x HN05S Hex Nut #8 - 32 LW03S... -
Page 16: Operator's Notes
OPERATOR’S NOTES... -
Page 17: Operation
OPERATION ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Grind Frozen Product. DO NOT Wear Gloves While Operating. -
Page 18: Cleaning
NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other Electrical Components. ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE MINI-22 MIXER GRINDER 1. Disconnect mixer grinder from power source and perform lockout/tagout procedures. 2. Remove end ring, breaker plate, knife and grinding auger. -
Page 19: Maintenance
NEVER Bypass, Alter or Modify This Equipment in Any Way From Its Original Condition. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. USE ONLY GENUINE BIRO Parts and accessories Properly Installed. GENERAL: Check all fasteners for tightness. Replace any missing fasteners. - Page 20 In addition, such practice will probably break the new member. Available Grinder knives and plates for Model Mini-22 MC22-17 Knife, Size 22, Standard Disposable MC22-18-125 Plate, Size 22, ⅛” (3,5mm) diameter holes...
-
Page 21: Operator's Notes
OPERATOR’S NOTES... -
Page 25: Three Phase Control Panel
Three Phase Control Panel for 208/220-60-3 64051 64045 64052 64054 64054 64053 GMC-12 GMC-12 GTK-22 GTK-22 64057 64056 64055 GROUND NOTE: For Mini-22 at 380-50-3 Transformer Item Number is 55048CE-1 Mixer Contactor/Overload is Item Number: 64054/64129 Grinder Contactor/Overload is Item Number: 64054/64055... -
Page 26: Operator's Notes
OPERATOR’S NOTES... -
Page 27: Operator's Signature Page
OPERATOR’S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS. DATE NAME (PRINT) SIGNATURE... -
Page 28: Limited Warranty
REGISTRATION CARDS: You must sign, date and complete warranty registration card supplied with each machine. The warranty card must be returned to the Biro Manufacturing Company for proper registration. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was originally shipped from the factory.