BIRO AFMG-48-II Operating And Service Manual
Automatic feed mixer grinder
Hide thumbs
Also See for AFMG-48-II:
- Operating and service manual (36 pages) ,
- Operating and service manual (36 pages)
Subscribe to Our Youtube Channel
Related Manuals for BIRO AFMG-48-II
Summary of Contents for BIRO AFMG-48-II
- Page 1 IMPORTANT NOTICE This Manual contains important safety instructions which must be strictly followed when using AFMG-48 this equipment. AFMG-48 138-4-08-13 138-9-05-12...
- Page 2 OPERATING AND MAINTENANCE INSTRUCTIONS 3. FOR NORD HELICAL – WORM GEAR AND MOTOR REDUCER NORD GEAR CORP. ELECTRICAL CONNECTIONS 800 Nord Drive Check the motor nameplate to verify the phase, hertz and P.O. Box 376 voltage agrees with the available power supply. Connection Waunakee, WI 53597-0367 should conform to local codes.
-
Page 3: Mixer Drive Belt Tension
4. FOR DORRIS MIXER TRANSMISSION DORRIS MIXER TRANSMISSION: Oil in the mixer transmission should be changed after the first four (4) weeks of operation. This is to remove the "run-in" oil and also any small metal shavings that may have been generated during the initial mating of the gears. -
Page 4: Chain Replacement
MAIN DRIVE CHAIN AND SPROCKETS LUBRICATION (continued): Recommended types of chain lubricant are those with Molybdenum Disulphide or Graphite added. Also bonded lubricants such as Dow Corning Molykote 321R or equivalent are excellent for open chains. The lubricant should be of a viscosity whereby it will “flow” somewhat and penetrate the internal working surfaces. Thick stiff greases are of little value because they cannot work into moving parts of the chain. - Page 6 — NOTES —...
- Page 7 AFMG-48 SIDE VIEW PARTS DIAGRAM...
- Page 8 BIRO MODEL AFMG-48-II MIXER GRINDER PARTS LIST Fig. Item No. Description Fig. Item No. Description 57154 Product mixer safety cover, tri directional, HHS055S Hex head screw -18 ´ ¾, SS #63592 on HN07S Hex nut 10-24, SS 53547 Lid with chute opening HN15S Hex nut ¼-20, SS...
- Page 9 Fig. Item No. Description 56221 Safety cover torsion spring, R.H., #63401 on 56222 Safety cover torsion spring, LH., #63401 on 57050 Safety cover hinge rod, #63401 on 57153 Tri directional hinge rod, for front opening, #63440 on 55095 Right side skirt, 90° inlet, #52001 to 56045 Hinge rod spacer (2 req'd) #52344...
- Page 10 OPTIONAL STAINLESS STEEL BOWLS, AUGERS & RINGS 114mm UNGER Item No. Description FHS33S Shear pin fastener ¼-20 ´ ½ SS HHS012S Hex head screw, 10-32 ´ HK114 Knife drive pin, 114mm Unger HR42/48S-114 End ring, SS, 114mm Unger LW05S Lock washer, #10, SS 52106S-114 Bowl, SS, 114mm Unger 54278-CTNS-114...
-
Page 11: Dorris Mixer Transmission Parts List
DORRIS MIXER TRANSMISSION PARTS LIST H369 Hex head screw -18 ´ ¾ 53769-38 High speed Timken cup (closed end) LW30S Lockwasher, SS " 53769-39 High speed Timken cone (closed end) 0850 Setscrew -20 ´ " long 53769-40 High speed Timken cup (open end) 1084 Hex head cap screw -13 ´... - Page 12 NO. 53886 JOURNAL BOX ASSEMBLY Item No. Description 53609 Journal box, #62001 on 53724 Auger drive shaft, #62001 on 53785 Journal box seal (2 ea.) 53886 Journal box assembly complete 53888, 53940 Front bearing cup/cone assembly Order H310A 53889, 53939 Rear bearing cup/cone assembly Order H311A 53993 Vented grease fitting...
- Page 13 TANDEM OPERATION PARTS LIST 272-7-1 -18 plastic knob – 3 pt. 53489 Dscg. Horn 24/42/46/48 to 24/48/52 inlet less seal 57044 Connec. brkt. AFMG52 to AFMG48 57044 Connec. brkt. AFMG52 to AFMG52 53552-1A Connecting brkt. assem. man/auto 53604 Dscg. horn 52 to 24/48/52 inlet 53667 Dscg.
- Page 14 TANDEM OPERATION ILLUSTRATION FOR 90° INLET FROM S/N 62001 TO S/N 63591...
- Page 16 TANDEM OPERATION ILLUSTRATION FOR 35° INLET S/N 63592 ON...
Need help?
Do you have a question about the AFMG-48-II and is the answer not in the manual?
Questions and answers