Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Strata ADVANCECUT 65
Summary of Contents for Strata ADVANCECUT 65
-
Page 1: Operating Instructions
ADVANCECUT 65 PLASMA CUTTER OPERATING INSTRUCTIONS DIRECT 400V 50HZ SPIKE/ INTELLIGENT CORROSION IGBT INVERTER PILOT CURRENT 3 PHASE GENERATOR RESISTANT TECHNOLOGY ARC START CUTTING PROTECTION SAFE SYSTEM www.strata.co.nz... - Page 2 ADVANCECUT 65 Congratulations on your new Strata product! The Strata range from Euroquip uses latest technology design and engineering to produce welding products that combine market leading value and features with durability. Designed for discerning operators who seek professional results and product quality without the price tag of a full professional setup.
-
Page 3: Table Of Contents
ADVANCECUT 65 Contents Know Your Machine............5 Quick Start Guide..............7 Available Parts & Accessories...........8 Wiring Diagram..............9 CNC Socket Diagram............10 Care & Maintenance............11 Plasma Cutting Guide............12 Other Knowledge & Resources........14 Troubleshooting............15 Safety................16 Warranty.................23 www.strata.co.nz... - Page 4 The powerful 3 phase Plasma Cutter in a tough compact package. With IGBT technology and the capability of severing up to 35mm carbon steel with CNC interface capability, look no further than the ADVANCECUT 65 for serious industrial cutting solutions. • IGBT module inverter technology for smooth, stable output, increased reliability • Microprocessor control system for superior...
-
Page 5: Know Your Machine
ADVANCECUT 65 Know Your Machine *Denotes more detailed explanation of function to follow. Front View Cutting Current Control Knob Power Indicator. Lights when input power connected and machine switched on Power Error/ Overload Indicator* Torch System Error Indicator* Cutting Power Indicator. Lights when cutting power circuit activated Air Control Run/ Set Switch * Earth Lead Connection Socket Plasma Torch Euro/ Central Connector CNC Interface Connection Port Rear View 10. Air Pressure Regulator Outlet Pressure Gauge 11. Air Pressure Regulator Knob 12. - Page 6 This is especially It is also very important to only use genuine Strata useful for starting cuts on material that does not have consumables and parts for the XT4000 torch. They...
-
Page 7: Quick Start Guide
Quick Start Guide - Plasma Cutter Installation Electrical Connection Basic Operation The ADVANCECUT 65 is designed to operate on a 3 1.1 Connect the earth cable quick connector to the phase 20A 400V AC power supply. earth connection socket (7) Connect the earth clamp to the work piece. -
Page 8: Available Parts & Accessories
Cutting Tip 0.8mm 20-30A (5Pk) XT4005-09 Cutting Tip 0.9mm 30-40A (5Pk) XT4005-10F Flat Cutting Tip 1.0mm 40-50A (5Pk) XT4005-08L Ext Cutting Tip 0.8mm 20-30A (5Pk) XT4005-09L Ext Cutting Tip 0.9mm 30-40A (5Pk) XT4003 Standard Electrode (5pk) XT4003L Extended Electrode (5Pk) XT4006 Gas Distributor XT4007 Retaining Cap XT4008 Double Pointed Spacer XT4001 Torch Head XT4011 Handle - Complete with Trigger These accessories listed are available from your Strata Supplier. Refer to the Strata Catalogue, your Strata Supplier or look online at www.strata.co.nz for other accessories and consumables available. www.strata.co.nz... -
Page 9: Wiring Diagram
ADVANCECUT 65 Wiring Diagram www.strata.co.nz... -
Page 10: Cnc Socket Diagram
ADVANCECUT 65 CNC Socket Diagram Pin No. Signal Comment 6, 7 Arc Signal 20:1, 6(+) 7(-) Torch Switch Signal Short circuit 8 and 9 equals to press torch switch. Disconnect 13, 14 for pilot arc. 13, 14 Pilot Arc Signal Connect 13 and 14 for cutting arc. www.strata.co.nz... -
Page 11: Care & Maintenance
ADVANCECUT 65 Care & Maintenance • Check for damaged parts. Do not use the plasma cutter with damaged parts. Keep your Plasma Cutter • A damaged plasma cutter must be carefully checked by a qualified person to determine that in Top Condition it will operate properly. Check for breakage of parts, mountings and other conditions that may affect its operation. -
Page 12: Plasma Cutting Guide
(normally a symptom of older, worn out compres- sors). The air hose must also be of sufficient size Effect of Cutting Speed (3/8”/10mm minimum) to supply the machine. Cutting with the ADVANCECUT 65 After turning the Power Switch to the ON position and TOO FAST TOO SLOW... - Page 13 ADVANCECUT 65 Piercing Technique the tip near (not touching) the edge of the work piece at the point where the cut is to start. When starting at the edge of the plate, do not pause at the edge and force the arc to ‘reach’ for the edge of the metal.
-
Page 14: Other Knowledge & Resources
ADVANCECUT 65 put line voltage, air pressure, etc. Generally there is Direction of Cut - The plasma gas stream swirls as it leaves the torch to maintain a smooth an inversely proportional relationship between output column of gas. This swirl effect results in one current and speed of cut. Do not use more output cur- side of a cut being more square than the other. -
Page 15: Troubleshooting
ADVANCECUT 65 Troubleshooting PROBLEM CAUSE SOLUTION • Power switch OFF • Turn power switch to the ON position • Air supply is not of sufficient volume or • Check air supply (60–80 PSI, 3.5cfm required) Torch will not come on pressure • Attach to work piece or to steel table with • Work piece ground clamp not attached. work piece securely clamped to table • Plasma torch is not piercing the material • Increase current • Torch may be too far away from the • Decrease the distance of your torch to the Sparks are shooting upward... -
Page 16: Safety
ADVANCECUT 65 2. Avoid unintentional starting. Make sure the plasma Safety cutter is setup correctly and you are prepared to be- gin work before turning on the plasma cutter. Store and Retain this Manual 3. Unplug before performing maintenance. Retain this manual for the safety warnings and pre- Always unplug the plasma cutter from its electrical... - Page 17 ADVANCECUT 65 WARNING! 10. Transportation Methods Lift unit with the handles Only use safety equipment that has been ap- provided, or use a handcart or similar device of ad- proved by an appropriate standards agency. equate capacity. If using a fork lift vehicle, secure the Unapproved safety equipment may not provide unit to a skid before transporting.
- Page 18 ADVANCECUT 65 Personal Safety CAUTION! not use a tool while you are tired or under the Keep the work area well lit. Make sure there is adequate space surrounding the work area. Al- influence of drugs, alcohol or medication. A mo- ment of distraction when operating equipment ways keep the work area free of obstructions, grease, oil, trash, and other debris.
- Page 19 ADVANCECUT 65 Arc Rays can Burn Eyes and Skin 4. If working on a metal wall, ceiling, etc., prevent ignition of combustibles on the other side by moving the combustibles to a safe location. If DANGER! relocation of combustibles is not possible, desig- Arc rays from the welding process produce...
- Page 20 ADVANCECUT 65 6. Turn off all equipment when not in use. Discon- 2. Do not plasma cut where flying sparks can strike nect power to equipment if it will be left unat- flammable material. tended or out of service. 3. Remove all flammables within 10m of the plasma cutting site.
- Page 21 ADVANCECUT 65 www.strata.co.nz...
- Page 22 ADVANCECUT 65 www.strata.co.nz...
-
Page 23: Warranty
No costs incurred will be considered under warranty if re- Registered warranty period for the ADVANCECUT 65: pairs are carried out by a party other than a Euroquip Ap- Commercial Use: 36 Months Domestic Use: 36 Months proved Service Agent, unless with prior consent in writing from Euroquip. - Page 24 Congratulations on your new STRATA product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This product is backed by our extensive warranty and world-wide service network. To locate your nearest distributor or service agency visit www.
Need help?
Do you have a question about the ADVANCECUT 65 and is the answer not in the manual?
Questions and answers