Accessories; Repairs; Environmental Protection; Troubleshooting - Metabo KGT 305 M Original Instructions Manual

13. Accessories

Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
CAUTION! The use of other tools and accessories
can result in a risk of injury.
A Spray for maintenance and care for the
removal of resin residues and to preserve the
metal surfaces.
B Extraction adapter "Multi" for the connection of
extraction hoses with 44, 58 or 100 mm adapter
0910058010
C Metabo all-purpose vacuum cleaner (see
catalogue)
D Stands:
Universal machine stand UMS:
Machine stand KSU 251:
Machine stand KSU 401:
E Roller stand:
RS 420
F Saw blade Precision Cut Classic
305 × 30 x 2.4 /1.8,56 WZ 5° neg
for longitudinal and transverse cuts in solid wood
and chipboard
G Sägeblatt Precision Cut
305 x 30 x 2,4/1,8 48 WZ 5° neg
for efficient longitudinal and transverse cuts in
solid wood and chipboard
H Saw blade Multi Cut
305 x 30 x 2.8/2.0 96 FZ/TZ 5° neg,
for longitudinal and transverse cuts in coated
materials, laminate, plastic and aluminium profiles
For a complete range of accessories, see
www.metabo.com or the catalogue.

14. Repairs

Danger!
Repair of power tools must be carried out by
qualified electricians only!
This power tool complies with the applicable
safety regulations. Repairs must only be carried
out by qualified electricians and using original
spare parts; otherwise the user faces a risk of
accidents.
If you have Metabo power tools that require
repairs, please contact your Metabo service
centre. See www.metabo.com for addresses.
Do not replace cutting area lighting (17) and
cutting laser (16) with another type.
You can download a list of spare parts from
www.metabo.com.

15. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately
and handed in for environmentally compatible
recycling in accordance with European Directive
2002/96/EC on waste electrical and electronic
equipment and its implementation in national
legal systems.

16. Troubleshooting

Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 14. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
 Disconnect the mains plug prior to any fault

service.

 Check that all safety devices are operational
again after each fault service.
Motor does not run
 No mains voltage:
 Check cables, plug, outlet and mains fuse.
No trimming function
Transport lock (18) locked:
 Pull out transport lock (18).
Transport lock (19) locked:
 Unhook transport lock (19).
Safety lock (8) locked:
0911018691
 Press safety lock (8)
Cutting power too low
Saw blade blunt (possibly tempering marks on
blade body);
Saw blade unsuitable for the material (see
chapter 13. "Accessories");
Saw blade contorted:
6.31317
6.29005  Replace saw blade (see chapter 11.
6.29006 "Maintenance").
Saw vibrates a lot
0910053353
Saw blade contorted:
6.28064
 Replace saw blade (see chapter 11.
"Maintenance").
Saw blade not installed properly:
 Install saw blade properly (see chapter 11.
6.28227
"Maintenance").
Turntable hard to turn
Chips under turntable:
6.28091
 Remove chips.
Upper table (13) cannot be lowered when
used as a table saw
 Fit side protection (12) correctly.

17. Technical Specifications

Explanatory notes on the specifications on page 4.
Subject to change in accordance with technical
progress.
U = mains voltage
I = Rated power
F = min. fuse protection
P = rated input power
1
IP = protection class
n = No-load speed
0
v = Max. cutting speed
0
D = largest / smallest blade diameter (outer)
d = saw blade hole (inside)
b = max. tooth width of the saw blade
c = thickness of the splitting wedge
A = dimensions (lxwxh)
m = weight
T = Ambient temperature range
Requirements for chip and dust extraction unit:
D = connection diameter of the extraction
1
nozzle
D = minimum air throughput
2
D = minimum negative pressure at extraction
3
nozzle
D = minimum air speed at extraction nozzle
4
H = cutting depth when used as a table saw
Maximum cross-section of the workpiece when
used as a chop and mitre saw, see table on
page 4.
~
AC Power
Machine in protection class II
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on the operating
conditions, the condition of the power tool or the
accessories. Please allow for breaks and periods
for assessment purposes when the load is lower.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three
directions) determined in accordance with
EN 61029:
a = vibration emission value
h
K = Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = sound-pressure level
pA
L = acoustic power level
WA
K , K = uncertainty
pA WA
Wear ear protectors!
ENGLISH en
19