Advertisement

Quick Links

Before commencing assembly please read these instructions thoroughly
LITTLE TONI EP
Wing Span:40 in / 1020 mm
Wing Area: 310 sq in / 20 sq dm
Flying Weight: 28 6 oz / 810 g
Fuselage Length: 36 in / 910 mm
Requires: 4- channel radio w/ 4 micro servos,
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
www thewingsmaker com
.
,
Specifications
Specifications
.
20A Brushless ESC and 3 cells 11 1V
2100 mAh Li Po battery
-
.
I NSTRUCTI ON M ANUAL
.
&
charger.
GE030
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LITTLE TONI EP and is the answer not in the manual?

Questions and answers

Summary of Contents for arf LITTLE TONI EP

  • Page 1 I NSTRUCTI ON M ANUAL Before commencing assembly please read these instructions thoroughly LITTLE TONI EP Specifications Specifications Wing Span:40 in / 1020 mm Wing Area: 310 sq in / 20 sq dm Flying Weight: 28 6 oz / 810 g...
  • Page 2: Before You Begin

    LITTLE TONI EP INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY P.3-P.9 SAFETY PRECAUTIONS BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
  • Page 3: Parts List

    Parts List 1. MAIN WING -- 1 pair 6. SCREW PB2x10mm -- 2 pcs CLEVIS -- 1 pc. 2. SERVO MOUNTING PANEL -- 1 pair FUEL TUBE d2xD4x4mm -- 1 pc. SCREW PB2x12mm -- 4 pcs HORN -- 1 set SCREW PA1.7x8mm -- 8 pcs PUSHROD Ø1.4x427mm w/ Threads (For Rudder) -- 1 pc.
  • Page 4 Main Wing Apply instant type CA glue to both sides of each hinge. Aileron Servo Lead Bottom View Ø1mm pilot holes for The Wings Maker horn are pre-drilled. Aileron Servos Please look for pin-hole marks at under side of control surfaces. PB2x12 mm Screw PA1.7x8mm Fuel Tube...
  • Page 5: Main Landing Gear

    Main Landing Gear PM3x25mm Screw Wheel Pant Wheel Ø 40mm d3xD7mm Washer PWA2x6mm Set Screw PWA2x6mm Screw PM3x25 mm PWA2x10mm Screw M3 Nut 3.1mm Collar Copper Tube M3 Nut Plate 0.5mm d3.1xD4x4mm Completed d3xD7mm Washer PWA2x10mm 3.1mm Wheel Collar Bottom View Stabilizer &...
  • Page 6: Rudder Pushrod

    Vertical Fin, Rudder & Tail Landing Gear M2 Nut PA2x8mm Screw Apply instant type CA glue to both sides of each hinge. PM2x8mm Screw C=C' Completed PA2x8mm Wheel 23mm Ø Plastic Collar M2 Nut PM2x8mm Bottom View Rudder Pushrod Ø1mm pilot holes for The Wings Maker horn are pre-drilled. PB2x10mm Screw Please look for pin-hole marks at under side of control surfaces.
  • Page 7: Elevator Pushrod

    Elevator Pushrod Pushrod Clevis Ø1.4x418mm 60mm 35mm Fuel Tube d2xD4x4mm Bottom View Outrunner Motor/ Cowling KP0011310 Solder Solder PWA2x8mm Screw Optional Parts PM2x12mm Screw Outrunner Motor 28/ 30 KM0283010 PM3x6mm PM3x6mm Screw d3xD7mm Washer d3xD7mm Washer Propeller Adaptor (d3xD5) Don't over-tighten the HW2340100 PM3 screws, too much stress on the screws...
  • Page 8: Radio Equipment

    Radio Equipment Install and arrange the servos as shown in the diagram. 20A Brushless ESC Elevator Servo Front Double-Sided Tape Straper Elevator Pushrod Ø1.4x418mm Sponge Fuel Tube Receiver d2xD4x4mm Rudder Pushrod Rudder Servo Ø1.4x427mm Bottom View Battery Battery Tie Top View Completed Main Wing PM2.5x20mm Screw...
  • Page 9 Canopy PWA2x8mm Screw 1.2mm PWA2x8mm Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A=A' B=B' C=C' D=D'...
  • Page 10: Control Throws

    # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. LITTLE TONI EP 180W Motor System...
  • Page 11 www.thewingsmaker.com THE WINGS MAKER GE030PO18130809...

Table of Contents