Indoor color mini dome camera, outdoor day/night 3-axis vandal dome camera, outdoor color 3-axis vandal dome camera, outdoor day/night ir 3-axis vandal dome camera, outdoor day/night mini bullet, indoor color non-functioning side view smoke detector camer (14 pages)
1080p full high definition true day/night box camera (14 pages)
Summary of Contents for EverFocus EQH5102
Page 1
EQH5102 1080p Mini Box Camera User’s Manual ...
Page 2
Cautions Please read this manual first to ensure correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV / radio transmitters, magnets, electric motors, transformers and audio speakers, because the electromagnetic fields generated by these devices may distort the video image or otherwise interfere with camera functions. 2. Never disassemble the camera beyond the recommendations in this manual, nor apply materials to it other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage. 3. Try to avoid pointing the camera toward the sun. In some circumstances, direct sunlight may cause permanent damage to the sensor and / or internal circuits. It may also create unbalanced illumination that may be beyond the camera’s ability to compensate. 4. Keep the power cable away from water and other liquids. Never touch the power cable with wet hands. Touching a wet power cable with your hands or touching the power cable with wet hands may result in electric shock. 5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may cause equipment failure, electric shock or, in extreme cases, fire. 6. Cleaning For cameras with interchangeable lenses, do not touch the surface of the sensor directly with your hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Do not use complex solvents, or corrosive or abrasive agents to clean any part of the camera. 7. Do not operate the camera beyond the specified temperature, humidity and power source levels. This camera is suitable for indoor operation only. ...
Page 3
Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in this case, the user may be urged to take adequate measures. This Product is RoHS compliant. Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end‐of‐life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for WEEE used electrical and electronic product. Please, help us to conserve the environment we live in! ...
EQH5102 1080p Mini Box Camera 1. Introduction The EQH5102 is an HDcctv indoor mini box camera. Based on a progressive scan CMOS sensor for HD 1080p resolution 100% digital images, it delivers vastly superior video quality compared to traditional CCTV images. This superior resolution not only captures more critical evidentiary information, but the inherent ability for megapixel video also extends the area of coverage, expedites completion of investigations, resolves complaints and reduces both capital and operational costs. No major upgrade to the IT network is required to deploy this powerful technology; HDcctv cameras communicate at digital speeds up to 1.5 Gb/s over existing or new coaxial cable (RG59 or other types for longer distances), using industry standard BNC connectors. The EQH5102 allows flexible choices of megapixel manual & DC iris control lenses with C / CS mount for outstanding coverage in a wide range of demanding surveillance environments while delivering stunning HD image quality. Packing List Camera body x 1 Lens Cover x1 Power Pigtail Cable x 1 C‐mount lens adapter x 1 ...
EQH5102 1080p Mini Box Camera 2. Overview No. Name Descriptions Connects to a HD device using a 75 Ohm BNC‐type coaxial 1 HDcctv Output cable. Use the joystick to configure the settings in the OSD 2 OSD Menu Joystick menu. Connects to a 12VDC power, RS‐485 and MD (Motion 3 Screwless Terminal Strip Detect) source. 4 Power LED Glows red then power is present. 5 Grounding Stud Ensuring a good grounding when used. Connects to a SD monitor for setting image aim and 6 Test‐Out focus. 3. Installation 3.1 Lens Installation and Adjustment You can install either a CS‐mount or a C‐mount lens into the camera. It is recommended to use ...
EQH5102 1080p Mini Box Camera If you are using a DC Auto Iris lens: Remove the cover cap from the camera body. Install the lens into the camera body. Connect the DC cable to the DC Auto Iris Lens Connector. Lock the Focus Screw. C‐Mount Lens: Remove the cover cap from the camera body. Install the lens into the camera body using the supplied C‐mount lens adapter. Adjust the lens using the Focus / Zoom Screws. Warning: Installing a C‐mount lens without the C‐mount lens adapter may damage the camera sensor. 3.2 Top / Bottom‐Mount You can use the supplied mounting bracket and screw it on the top of the camera body to suspend the camera, or on the bottom of the camera body to support the camera. 4. Basic Connection Connect the camera to an HD device, such as an HDcctv DVR, to display the image. Connect the camera to a 12VDC power source using the supplied Power Cable. You can optionally use the supplied Power Pigtail Cable or a power adapter to connect the Power Cable to the power source. The power LED will be lit in red. Connect the camera to a CVBS portable monitor for setting image aim and focus before mounting the camera. 5. Configuration in the OSD Menu You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD ...
EQH5102 1080p Mini Box Camera 5.1 OSD Menu Press the Enter / Confirm button on the Joystick. The Setup Menu in the OSD appears. 5.1.1 EXPOSURE Press the Enter / Confirm button to enter the submenu. BRIGHTNESS Use the and buttons to increase or decrease the screen brightness from 0 to 20. MODE Indoor Select this mode when the color temperature of the video image is similar to that found in indoor environments (around 5100 to 5300°K). Outdoor Select this mode when the color temperature of the video image is similar to that found in outdoor environments (around 3,000°K to 3,200°K) ...
Page 9
EQH5102 1080p Mini Box Camera Shutter Use the and buttons to adjust the shutter speed. The options include: 1/25 ~ 1/60000, FLK, and AUTO. Any selection other than AUTO and 1/25 will disable the DSS function. DSS DSS is used to maintain a vivid screen image by automatically boosting low light levels. The value is between x2 ~ X4 and OFF. AGC (Auto Gain Control) The higher the AGC value, the brighter the screen, but the level of noise will also be increased. The options include: 0~10. 5.1.2 COLOR Press the Enter / Confirm button to enter the submenu. AWB (Auto White Balance) This mode can be used to view areas with a color temperature range. Use the and buttons to select the AWB options. The options include: AUTO, AUTO EXTN, PRESET, MANUAL COLOR TEMP, R‐GAIN and B‐GAIN. AUTO – Around 2500 to 9500°K ...
Page 10
EQH5102 1080p Mini Box Camera 5.1.3 IMAGE Press the Enter / Confirm button to enter the submenu. SHARPNESS Use the and buttons to increase or decrease the SHARPNESS from 0 to 10. MIRROR/FLIP Turn it on to reverse/ flip the image. DZOOM Turn it on to set up the zoom level PRIVACY Enter the submenu to set up the privacy masks; up to 31 zones can be created: ON ZONE NO: Use the and buttons to select the zone from 0 to 31. X, Y‐POS, SIZ: Enter the submenu to set up the position or size of the privacy mask zone. COLOR: Press to select a color for the selected privacy mask zone. TRANS: Press to select the transparency of mask zone. ...
Page 11
EQH5102 1080p Mini Box Camera illumination. DAY&NIGHT The options include MODE, AGC THRS, DELAY. A submenu can be entered if you select MODE. MODE – Use the and buttons to select AUTO, COLOR and B&W. Switches to a B&W feed in low light conditions and then switches back to a Color feed in the daytime. AGC THRS –Use the and buttons to select the AGC Threshold from 0 to 20. DELAY – Set up the delay time in 0,5,10 and 30 seconds for the camera to switch between Day and Night. HLMASK Turn it on to select the level and color of the masking effect. CTB Turn it on to deliver properly exposed images despite bright light sources, deep shadows and/or unbalanced lighting in the same scene GAMMA Use the and buttons to increase or decrease the GAMMA from 0.45 to 0.75. 5.1.4 WDR/BLC Press the Enter / Confirm button to enter the submenu. MODE ...
Page 12
EQH5102 1080p Mini Box Camera Use the and buttons to select OFF, BLC and WDR. Please notice the WDR is only working on round 7.5FPS. WDR_WGT Use the and buttons to increase or decrease the WDR weight from 0 to 4. BLC OSD, POS and SIZ Select OFF to disable the BLC function, or select ON to enable the BLC function and for further setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign displayed on the screen. Use the direction buttons to move the area to the desired position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen. Use the direction buttons to adjust the size for the area. 5.1.5 3D‐DNR Press the Enter / Confirm button to enter the submenu. Switch to HIGH, MIDDLE, LOW and OFF to enable or disable noise reduction on dynamic recordings. 5.1.6 MOTION Press the Enter / Confirm button to enter the submenu. ...
Page 13
EQH5102 1080p Mini Box Camera RESOLUTION Use the and buttons to increase or decrease the RESOLUTION level from 0 to 4. SENSITIVITY Press to set up the sensitivity for the motion detection function. WINDOW TRANS Press to select the transparency of motion detect zone. WINDOW USE, POS and SIZ Select OFF to disable this function, or select ON to enable and for further setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign displayed on the screen. Use the direction buttons to move the area to the desired position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen. Use the direction buttons to adjust the size for the area. 5.1.7 SYSTEM Press the Enter / Confirm button to enter the submenu. ...
Page 14
EQH5102 1080p Mini Box Camera DEFECT DET Press to select the DPC (Defective Pixel Correction) level of defect detector. Please notice; do not use this function without cover the lens. The camera will automatically correct pixel defects. Misoperation will cause the abnormal image. CAM TITLE Switch to On and then enter the submenu to set up a camera name displayed on the screen. RS‐485 Use the and buttons to select ID, BAUDRATE, PROTOCOL and ID DISPLAY. The default of protocol is EVF‐1 (EverFocus). Version Press to display the firmware version of the camera. DOUT There are 4 options including 1080p 30FPS NTSC, 1080p 25FPS PAL, 720p 60FPS NTSC and 720p 50FPS PAL Language Select a language for the OSD text. Options include English, French, German, Simplified Chinese, Korean and Japanese. ...
EQH5102 1080p Mini Box Camera Operating Environment 0°C~45°C/32°F~113°F (20%~80% Humidity) Dimensions(L x W x H) 89 x 46 x 48mm /3.5” x1.8” x1.9” Weight 0.193kg/0.434lbs Certifications FCC / CE 7. Appendix 7.1 OSD Menu Structure The default value is marked with a star “*”. Main Sub Menu Sub Menu / Function . BRIGHTNESS 1~20 (default=6) MODE INDOOR*, OUTDOOR LENS MANUAL, DC* AUTO* 1 EXPOSURE SHUTTER MANUAL 1/25~1/60000 FLK ...
Page 17
EQH5102 1080p Mini Box Camera ON ZONE NO 0~31 ZONE UP ON, OFF X‐POS 0~60 Y‐POS 0~40 X‐SIZ 0~60 Y‐SIZ 0~40 COLOR TRANS 0~4 SHADING ON*, OFF AUTO* NODE COLOR B&W DAY&NIGHT AGC THRS 0~20 (default=10) MARGIN 0~20 (default=) DELAY 0, 5*, 10, 30 SEC OFF* HLMASK LEVEL 0~20 (default=10) ON COLOR BLK*/WHT/YEL/CYN/GRN/MAG/RED/BLU CTB ON, OFF* GAMMA ...
Page 18
EQH5102 1080p Mini Box Camera DEFECT DET DPC LEVEL 000~255 (default=26) OFF* CAM TITLE STRING SET ON POSITION ID 1~255 (default=1) BAUDRATE 2400, 4800, 9600*, 19200, 38400, 57600, 115200 RS‐485 PROTOCOL PELCO‐D, PELCO‐P, EVF‐1* ID DISPLAY ON, OFF 7 SYSTEM DOUT SCALE FULL*, COMP DOUT 720P, 1080P* FORMAT DOUT FPS 50, 60 ,25*, 30 FREQ 50*, 60 HZ CVB PAL*, NTSC LANGUAGE English, Simplified Chinese, Japanese, Korean RESET ON, PUSH ...
Page 19
Suite 803, Housefin Bhavan, C‐21, Bandra Kurla Complex, Bandra (East), Mumbai 400051, India TEL: +91 22 6128 8700 FAX: +91 22 6128 8705 www.everfocus.in sales@everfocus.in Ihr EverFocus Produkt wurde entwickelt Your EverFocus product is designed und hergestellt mit qualitativ and manufactured with high quality hochwertigen Materialien und materials and components which can Komponenten, die recycelt und wieder be recycled and reused.