Indoor color mini dome camera, outdoor day/night 3-axis vandal dome camera, outdoor color 3-axis vandal dome camera, outdoor day/night ir 3-axis vandal dome camera, outdoor day/night mini bullet, indoor color non-functioning side view smoke detector camer (14 pages)
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. EverFocus Electronics Corp. 12F, No. 79, Sec. 1, Shin-Tai Wu Rd., His-Chi, Taipei Hsien, Taiwan, R.O.C. EQN2200/2201 complies with CE and FCC rules.
Page 3
EQN2200/2201 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.
Page 4
Java-related logos and trademarks are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. Support If the unit ever needs repair service, the customer should contact the nearest EverFocus Electronics Corp. Service Center for return authorization and shipping instruction. About this AC Adaptor...
EQN2200/2201 1. INTRODUCTION EQN2200/EQN2201 is a 2 Megapixel network camera which has a highly compact housing design but superior image quality with up to 30fps in 720p resolution. For easy and flexible installation, EQN2200/EQN2201 offers the choice of either a wireless or a wired connection to the network.
Location/Address field of your Internet Explorer browser in the form http://nn.nn.nn.nn:port, or http://ddnsname.everfocusddns.com. (Please refer to EQN2200/2201 Installation Guide for how to find the IP address by using the IP Finder) Step 3. At the login popup window enter “Username” and “Password”. Default Username is “user1”...
Page 9
[System Info], [User Config], [Network], [Video], [Audio], [User], [Event] and [System]. Please refer to “Section 5 .Setting” for further information. Press button to close the EQN2200/2201 network page. ○ Video Stream ○ Select the desired Video Stream from H.264 and MJPEG. Please refer to "Section Streaming 5.4.1 Video...
Page 10
EQN2200/2201 Record ○ he record button is used to record the current video stream. The location where the image file is saved can be specified in Set ting -> User Config. Please refer to “Section 5.2 User Config” for further information. The “Record” icon turn s into red when it is cording.
EQN2200/2201 Event signa ○ When an alarm or motion event is triggered, a signal icon will flash to alert the user. The first icon is for alarm events and the other 5 icons are for motion events. The motion event icons, which differ by color, correspond to the motion trigger areas set in the Motion menu.
EQN2200/2201 5.1.1 Information Tab System Information: Firmware version, MAC address and Model number. (this data may not be chan ged in this page and is for reference only) 5.1.2 Log Tab...
EQN2200/2201 System Log: Date/Time: displays date and time of the log event. Log message: all information and event message, including login, user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records.
Page 14
EQN2200/2201 Position: Select the position where the text will be displayed: Upper Left / Lowe Right / Lower Left. Press Apply to apply the setting changes or Reset to reset without saving the changes. Date/T ime Format Used in Text...
EQN2200/2201 Note: 1. All languages can be removed, except English. 2. A maximum of five languages can be added in the language list. 3. Uploading a new language file will reboot the system automatically. Please reconnect to the IP camera after reboot.
Page 16
EQN2200/2201 IP Settings • IP Type • IP address • Subnet mask • Gateway (when using the gateway server/router) • Primary DNS, Secondary DNS (when using DNS) IP Type DHCP: Configure the DHCP server not to assign the same IP addresses used for e other network cameras and PCs whose IP address is unique.
Page 17
EQN2200/2201 Primary DNS An IP add ress of DNS server that is provided by ISP. This address may be assigned auto matically if DHCP is used. A correct DNS IP is essential if DDNS will be used. Secondary DNS If your ISP provides you an IP address secondary DNS, please set it here.
○ www.no-ip.com ○ Enable: Check the box to enable DDNS setting. Service ISP: If you choose EverFocus DDNS server, you can easily register a DDNS name and obtain free DDNS services from EverFocus ”www.everfocusddns.com ”. Enter an IP Cam Account Name: .everfocusddns.com...
EQN2200/2201 necessary to configure Record ID, FQDN, Username and password and register in advance for DDNS services. Refer to the web site for further information about the DDNS provider. Press Apply to apply the setting changes or Reset to reset without saving the change.
Page 20
EQN2200/2201 Password: Input the password if the SMTP server requires authentication. Receiver Address: Input the e-mail address to receive an e-mail message when the EVENT is enabled and triggered. Please use “; “ to separate address. ddress: Input sender’s e-mail address, so that receiver can recognize Sender A e sender when an event message is sent out.
EQN2200/2201 5.3.4 Network Alarm (reserved for PowerCon) Set Network Alarm his function is reserved for PowerCon software, for the details regarding these settings please refer to the documentation for the PowerCon network alarm rotocol.
EQN2200/2201 5.3.5 Wireless (For EQN2201 only) Wireless Setting able Wireless (Default: disable) Name o f the wireless network the camera is configured for. The field accepts up to 32 alphanumeric characters. The name must be exactly the same as the one used in the wireless access point or the connection will not be established.
Page 23
EQN2200/2201 A-F) characters for 128-bit WEP. ) Authentication: Open or Shared (Default: Open) “Open” – communicates the key across the network. “Shared” – allows communication only with other devices with identical WEP settings. Key Length: 64 or 128 bits (Default: 64 bits) Key Format: HEX or ASCII (Default: HEX) Network Key: Entering a key in either hexadecimal or ASCII format.
EQN2200/2201 5.4 Video The settings relating video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs: the [Video S treaming] tab and the [Camera] tab. 5.4.1 Video Streaming The system can output dual streams of H.264 and MJPEG simultaneously. For ach of them, user can set resolution, quality and frame rate individually.
Page 25
EQN2200/2201 t Rates: 3M/2M/1.5M/1M/750K/500K/384K/256K/128K/64K/32K bit/s - Constant Bi CBR allows you to set a fixed Target bit rate that consumes a predictable amount of bandwidth. As the bit rate would usually need to increase for increased image activity, b ut in this case cannot, the frame rate and image quality are affected negatively.
EQN2200/2201 change. 5.4.2 Camera Image Settings Brightness: to increase or decrease object contrast of images. It is adjustable from 0~100. Saturation: to increase or decrease color saturation of video images. It is adjustabl e from 0~100. to increase or decrease object sharpness of images. It is adjustable Sharpness: from 0~100.
Sets a vertical image inversion OFF: disable flip function. 5.5 Audio e EQN2200/2201 camera can transmit audio to client PCs by built-in microphone, and can play audio received from client PCs into built-in speaker. This section scribes how to configure the basic audio settings.
EQN2200/2201 Audio Check Enable Audio box to enable audio function. udio Input volume: Adjust the Audi o Input Volume for the audio input devices onnected to the camera if there are problems with the sound input being too low r high.
EQN2200/2201 Maximum 10 user IDs can be created to access the IP camera. The user formation screen displays the authorized IDs. Access levels are: • Supervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menus and can determine the registration of all other users. Howev an administrator is not allowed to change a supervisor’s account and password.
EQN2200/2201 Note: Up to 4 events can be configured in the camera, and up to 3 of these can be configured to upload images. 5.7.1 Event List The settings relating to event occurrences such as settings for motion, alarms time mask can be configured on this page.
Page 31
EQN2200/2201 This example describes how to set the camera to trigger alarm output as well as to upload image to FTP when someone presses Manual Trigger button: 1. Click button in Event page. 2. Enter an event name for the event, e.g. Event 1 3.
EQN2200/2201 5.7.2 Motion Detection Motion Detection Users can define the motion areas to be de tected by left clicking the mouse to set the start point. Then click the mouse again at the end point, a rectangle will be formed as the motion detection area.
EQN2200/2201 5.7.3 Event Settings Alarm Settings Input Triggering Type: Select from Normal Close or Normal Open. Output Contact Type: Select from Normal Close or Normal Open. Output Duration Time: Select duration time of alar m output from 5 sec, 10 sec, 20 sec, 30 sec, 60 sec, 2 min, 3 min and 5 min.
EQN2200/2201 Image saved internally in the camera from the time Post-Alarm Buffer: immediately after the trigger condition has ceased/been reset. Input the desired length of post-trigger buffer time. It can be set up to 120 seconds. Press Apply to apply the setting changes or Reset to reset without saving the change.
EQN2200/2201 How to set a schedule: Select the edit actions of “select” or “deselect”. There are 24 blocks (one block = 1hr) on the time bar representing 24 hours respectively. Set a schedule start time by clicking on a desired start time block on a time bar.
Page 36
EQN2200/2201 snapshot folders created on a user’s PC. Press Apply to apply the setting changes or Reset to reset without saving the change. et Time Zone Time Zone: Select a time zone according to where the camera is located. Press Apply to apply the setting changes or Reset to reset without saving the change.
EQN2200/2201 5.8.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving. Set the start time for daylight saving time. et the start week for daylight saving time: 1 / Last Set the start day of the week for daylight saving time: Sunday / Monday / Tuesd...
EQN2200/2201 Press Apply to apply t he setting changes or Reset to reset without saving the change. 5.8.3 Maintenance aintenance Server Reboot: The unit is rebooted without changing any of the settings. U se this method by pressing Reboot button if the unit is not behaving as expected.
Page 39
(see above) and then click the Load button. The settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EQN2200/2201 with the latest firmware. Press the Browse button to locate the firmware file. Press the Upgrade button to upgrade the firmware.
Page 40
803, 8th Floor, ousefin Bhavan, -21 Bandra Kurla Complex, andra (East), Mumbai 400 051 l: +91 22 6128-8700 Ihr EverFocus Produkt wurde entwickelt Your EverFocus product is designed und hergestellt mit qualitativ and manufactured with high quality hochwertigen Materialien und...