Advertisement
Advertisement
Table of Contents
Related Manuals for Wallbox PULSAR
Summary of Contents for Wallbox PULSAR
- Page 1 & drive PULSAR INSTALLATION GUIDE PULSAR - installation guide...
- Page 2 FOR MORE INFORMATION: https://www.wallbox.com/en/support/ sales@wallbox. c om PULSAR - installation guide en 2...
- Page 3 Disregard of or actions contrary to the safety information and instructions contained in this manual and printed on the device, may lead to electric shock, fire and/or severe injury and can either damage the vehicle’s battery or the Wallbox device. Any resulting damage from such actions is excluded from the warranty.
- Page 4 INDEX SAFETY INSTRUCTIONS PRODUCT DESCRIPTION UNBOXING & CHECKLIST INSTALATION INSTRUCTIONS 4. 1 DIMENSIONS &POSITIONING DRILL & MOUNT STARTUP TROUBLE SHOOTING & MAINTENANCE WARRANTY PULSAR - installation guide...
-
Page 5: Safety Instructions
Relative humidity Between 5% and 95% (Non condensing) ¹ Do not use your wallbox Pulsar under inclement weather conditions that could a ect either the vehicle or the charging device itself. Do not open the connector panel cover in the rain. - Page 6 If the connector emits smoke or starts melting, never touch the charging cable. If possible, stop the charging process. In any case, disconnetc the power supply of the Wallbox charger. Make sure that the charging cable is out of reach of children. The charging cable may only be used by persons with a valid driver's license for motor vehicles.
-
Page 7: Product Description
The Wallbox device has been conceived for private and semi-public use, in such places as private land, company car parks and depots. The Wallbox device is used exclusively for charging electric and plug-in hybrid vehicles. - Page 8 PRODUCT DESCRIPTION 2/3 INFORMATION SUMMARY GENERAL Model name Pulsar Type 2 Pulsar Type 1 Mode Mode 3 Mode 3 Overall dimensions (w/o connector) 160x160x90mm 160x160x90mm Weight 3,0-4,0 Kg depending on cable length 3,0-4,0 Kg depending on cable length Operating temperature Between 25ºC and 45ºC...
- Page 9 PRODUCT DESCRIPTION 3/3 IDENTIFICATION OF YOUR WALLBOX On your Wallbox device you will find the following identification plate WB- PLSR0101A 32A 230/400VAC 50Hz 3P+N+PE IP 54 DATE: 20/01/16 Made in EU 0 602938 062800 S/N: 000001 Network settings Disposal information...
-
Page 10: Unboxing & Checklist
3x 6,3x40mm Screws 3x Ø8mm Wall anchors 2x RutaSeal® 3x Rubber plugs 1x Torx ¹ If any of the described items is missing, please contact www. w allbox. c om/support or service@wallbox. c om PULSAR - installation guide en 10... -
Page 11: Installation Instructions
INSTALLATION INSTRUCTIONS The electrical installation of your wallbox must be performed by a qualified electrician in accordance with the applicable norms and standards. You must consider the local electrical installation regulations, fire prevention measures and accident prevention regulations as well as emergency routes at this site. -
Page 12: Dimensions &Positioning
DIMENSIONS & POSITIONING Before selecting the mounting situation of your Wallbox , please read the following tips and references: According to the product standard, the charging station must be located at a height between 1.30 m and 1.70 m. We recommend you to mount the charging station at a height of 1. 6 0 m. -
Page 13: Drill & Mount
Step 0: In the backside of the Wallbox charger you will find an insertion with a thinner wall; use a cutter, razor or a sharp tool and carefully make an incision into the cable opening. Please meticulously remove all sharp edges. Take a Rutaseal bushing and install it. - Page 14 Proceed to fix your charger to the wall. Insert the screws in the positions marked, starting at the top one, and continuing clockwise. A B C Verify that your wallbox Commander is firmly attached and insert the plugs to complete this process. Step 2: Use the selector to choose the maximum operating current of the supply connection.
- Page 15 Reconnect the cover communication cable, and close the front cover taking special care of the fitting and that the O-ring sealing remains in place. Communication cable O-ring sealing Step 7: Secure the cover by screwing the Torx provided as shown in the picture below PULSAR - installation guide en 15...
-
Page 16: Startup
STARTUP Once the DRILL & MOUNT process is completed your Wallbox Pulsar is ready to operate. But first lets take a moment to read and review some useful information before starting to use your Wallbox Pulsar Do not use your Wallbox Pulsar for purposes not described in the Product description chapter. -
Page 17: Troubleshooting
Remember to ensure that the power supply is turned o , before you start cleaning your Wallbox Pulsar. In case you want to clean your Wallbox Pulsar, we recommend you to use a soft dry or damp cloth. Do not use a spray or direct water to clean your Wallbox Pulsar. -
Page 18: Warranty
Or you can call our technical support (Local call rates may apply): +39 0694804494 In case your Wallbox Pulsar needs to be repaired or replaced to correct manufacturing defects please provide us with a description of the issue including serial number and date of manufacture of your Wallbox Pulsar. - Page 19 Specifications are subject to change due to ongoing technical development. No guarantee is o ered in respect of any of the specifications given here. All rights reserved. In no event shall Wallbox Chargers S.L be liable for incidental or consequential damages arising from use of this document or the software and hardware described in this document.
- Page 20 & drive Italia P: +39 0694804494 E: sales@wallbox.com www. w allbox. c om PULSAR - installation guide...
Need help?
Do you have a question about the PULSAR and is the answer not in the manual?
Questions and answers