Hakko Electronics fm-206 Instruction Manual

Multi Rework Station
Instruction Manual
Thank you for purchasing HAKKO FM-206 Rework System.
Please read this manual before operating the HAKKO FM-206.
Keep this manual readily accessible for reference.
1. PACKING LIST
Please check to make sure that all items listed
below are included in the package.
HAKKO FM-206 1 ■Use this product with the following models.
Power cord 1
Tip tray 1 HAKKO FM-2027 (Soldering Iron)
Instruction manual 1 MODEL FM-2022 (Parallel Remover)
MODEL FM-2023 (Mini Parallel Remover)
MODEL FM-2024 (Desoldering Tool)
HAKKO FM-2026 (Soldering Iron N2 Type)
HAKKO FM-2029 (Hot Air Handpiece)
HAKKO FM-2030 (Heavy Duty Soldering Iron)
HAKKO FM-2031 (Heavy Duty Soldering Iron N2
HAKKO FM-206
*Each Hakko handpiece with the exception of the HAKKO
FM-2027 has their own instruction manual. Please refer to
this manual for specifications and replacement parts.
Power cord
Tip tray
2. SPECIFICATIONS
● Station
Power Consumption MAX 410W (450W)
Output
Temperature Range HAKKO FM-2026/2027 200 - 450℃ (400 - 840℉)
MODEL FM-2022/2023 200 - 400℃ (400 - 750℉)
Dimensions (W x H x D)
MODEL FM-2024 350 - 450℃ (660 - 840℉)
Weight
HAKKO FM-2029 100 - 550℃ (200 - 1030℉)
Capacity (Max)
HAKKO FM-2030/2031 200 - 500℃ (400 - 930℉)
Vacuum Generator
Temperature Stability ±5°C (±9°F) at idle temperature
Vacuum Pressure (Max.)
CAUTION Suction Flow
Power consumption is different depending on
● HAKKO FM-2027
Standards.
Power Consumption
Tip to Ground Resistance
* The temperature was measured using the HAKKO FG-101
thermometer. Tip to Ground Potential
* This product is protected against electrostatic discharge.
Cord
* Specifications and design are subject to change without
Total Length (w/o cord)
notice.
Weight (w/o cord)
Instruction manual in the language of Japanese, English, Chinse, French, German and Korean
can be downloaded from the HAKKO Document Portal.
(Please note that some languages may not be available depending on the product.)
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL:+81-6-6561-3225 FAX:+81-6-6561-8466
http://www.hakko.com E-mail:sales@hakko.com
×
連接部
OVERSEAS AFFILIATES
×
隔離器
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
×
電路板
TEL: (661) 294-0090 FAX: (661) 294-0096
×
插座
Toll Free (800)88-HAKKO
電磁蓋 ×
4 2 5 5 6
http://www.hakkousa.com
真空泵組件 ×
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
螺釘 ×
TEL: 2811-5588 FAX: 2590-0217
坦克組件 ×
http://www.hakko.com.hk
排出閥門 ×
E-mail:info@hakko.com.hk
SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: 6748-2277 FAX: 6744-0033
http://www.hakko.com.sg
E-mail:sales@hakko.com.sg
Please access to the following address for the other Sales affiliates.
http://www.hakko.com
Copyright © 2013 HAKKO Corporation. All Rights Reserved.
3. WARNINGS, CAUTIONS, NOTES AND EXAMPLES
Warnings, cautions and notes are placed at critical points in this manual to direct the operator's attention to
significant items. They are defined as follows:
WARNING: Failure to comply with a WARNING may result in serious injury or death.
CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved.
NOTE: A NOTE indicates a procedure or point that is important to the process being described.
When power is ON, the tip will be hot. To avoid injury or damage to personnel and items in the work
area, observe the following:
● Do not touch the tip or the metal parts near the tip.
● Do not allow the tip to come close to, or touch, flammable materials.
● Inform others in the area that the unit is hot and should not be touched.
● Turn the power off when not in use, or left unattended.
Turn the power off when connecting the handpieces or storing the HAKKO FM-206.
●
This appliance is not intended for use by persons (including children) with reduced physical, sensory
●
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
●
4. INITIAL SETUP
■Part Names
Power Switch
Type)
Control Button(1, 2, 3)
Filter Case Cover
Jack
(equipotential)
24V
162 × 136 × 245 mm (6.4 × 5.4 × 9.7 in)
6.2 kg (13.7 lb.)
6L/min.
Vacuum pump, cylinder type
80kpa (600 mm Hg) (24 in. Hg)
14L/min.
70 W (24 V)
< 2 Ω
< 2 mV
■Setup
1.2 m (4 ft)
●Hooking up the iron and connecting cable.
188 mm (7.4 in.) with 2.4D tip
30 g (0.067 lb./1.07 oz.)with 2.4D tip
Connection for
FM-2024 Suction
Hose
Plug the iron's connector
cord into the receptacle.
○ ○ ○ ○ ○
○ ○ ○ ○ ○ CAUTION
○ ○ ○ ○ ○
• Please make sure the power is off when you plug in cables.
○ ○ ○ ○ ○
• Please make sure to hook up the connector cable and the iron holder on the same
○ ○ ○ ○ ○
○ ○ ○ ○ ○ channel and not to place the iron in a holder connected to a differing channel.
○ ○ ○ ○ ○
• Please take care not to mix up the hose connections, the MODEL FM-2024 connects
○ ○ ○ ○ ○
to the filter case cover and the HAKKO FM-2029 to the air output.
○ ○ ○ ○ ○
• Securely insert the connecting cable all the way in to the jack.
2013.3
MA02390XZ130325
CAUTION
Control Knob
Flow Control Knob
Air Output
Compatible with
FM-2022
Compatible with Compatible with
FM-2024 FM-2023 FM-2024
* Each receptacle connector differs, please be careful not to connect an
FM-2026 FM-2024 FM-2026
incompatible device. Errors will result.
FM-2027 FM-2026 FM-2027
**For connecting iron holders. Make sure to connect the correct holder.
FM-2027 FM-2029
FM-2030 FM-2030
While both vacuum and hot air can be used, only one can be operated at once. One
FM-2031 FM-2031
cannot use a combination of hot air and vacuum or two vacuums simultaneously.
Receptacle* (1, 2, 3)
Power
Connection for
Cable
FM-2029 Air Hose
Connecting
Cable
Plug in power and connecting cables.
To prevent accidents or damage to the HAKKO FM-206, be sure to observe the following:
●
Do not use the HAKKO FM-206 for applications other than soldering.
●
Do not strike the iron against hard objects to remove excess solder. This will damage the iron.
●
Do not modify the HAKKO FM-206.
●
Use only genuine Hakko replacement parts.
●
Do not allow the HAKKO FM-206 to become wet, or use it with wet hands.
●
Remove power and iron cords by holding the plug − not the wires.
●
Be sure the work area is well ventilated. Soldering produces smoke.
●
While using HAKKO FM-206, don't do anything which may cause bodily harm or physical damage.
●
Jack
Power
(for foot switch)
Receptacle
I/O CoverPlate
Fuse
Jack**(1, 2, 3)
●Replacing the tip (HAKKO FM-2027)
CAUTION
The tip may be hot. Avoid holding the hot tip for a long time even if
using the heat-resistant pad. Otherwise burns may result.
Removing the tip:
● Hold down the lock release buttons in the sleeve assembly, pull out
the tip together with the sleeve assembly from the connector.
CAUTION
• Be sure to keep the lock release buttons held down while pulling
out the sleeve assembly. Failure to do so will damage the locking
mechanism.
• Be sure to pull out the tip only after separating the sleeve assembly
from the connector. Otherwise, the sleeve assembly may fall down
and break.
● While holding the front end of the sleeve assembly, pull out the tip.
Insert the tip:
Reassemble in the reverse order of disassembly.
●
CAUTION
• Insert the tip into the sleeve assembly until it clicks into place. When
you hear it click, avoid forcing the tip into the sleeve assembly.
• When holding the head of the tip, there is a danger of burn. Be sure
to use the heat-resistant pad.
*Each Hakko handpiece with the exception of the HAKKO
FM-2027 has their own instruction manual. Please refer to
this manual for specifications and replacement parts.
■Switch, Control Button and Knob Usage
Control Knob Usage
Use to change settings
Turning the control knob:
Changes setting values
or moves the cursor
Pushing the control knob:
Power switch
Makes selection
Use the power switch to turn
the power on and off.
Control Buttons
Use to change settings such as
temperature.
When pressed briefly:
Displays the preset screen.
When pressed and held:
Displays the change settings
screen.
Change Settings Screen Details
1. Temperature Settings
2. Offset Settings
3. Preset Temperature Settings
4. Preset Names
5. Channel Power (On/Off)
6 Exit
Flow Control Knob
When HAKKO FM-2029 is connected to
HAKKO FM-206, air flow will be displayed.
By turning the flow control knob, air flow
can be changed.
CH1 CH2 CH3
350 Off
℃ Ready
1 0 0 % M
SOL
* If you press a control button while on the Preset or Change
Settings screen, the corresponding channel screen will be
displayed.
Plugged in irons will be heated according to the settings
when the power is turned on.