Table of Contents
Advertisement
Submenu
Setting
[RGB Range]
When [RGB/YCC Range Auto] is set to
[Off] and the signal is RGB, select from
the following:
[YCC Range]
When [RGB/YCC Range Auto] is set to
[Off] and the signal is YCbCr, select
from the following:
[Col. Space/Mtx.
Select how to set the color space and
Auto]
transfer matrix.
[Color Space]
Select the color space from the
following:
Note
This setting can be set only when [Col.
Space/Mtx. Auto] is set to [Off].
[Transfer Matrix]
Select the transfer matrix from the
following:
Set the following depending on the
[Color Space] setting.
When [ITU-R BT.2020] is selected:
Select [ITU-R BT.2020].
When [ITU-R BT.709] is selected:
Select [ITU-R BT.709].
When another item is selected: Select
the transfer matrix setting of the device
which outputs the signal.
Note
This setting can be set only when [Col.
Space/Mtx. Auto] is set to [Off].
32
Adjustment Using the Menus
[Full]: 0 to 1023 (10bit) / 0 to 4095
(12bit)
[Limited]: 64 to 940 (10bit) / 256 to
3760 (12bit)
[Full]: 0 to 1023 (10bit) / 0 to 4095
(12bit)
[Limited]: 64 to 940 (10bit) / 256 to
3760 (12bit)
[On]: Use the color space and transfer
matrix according to the input
signal information.
[Off]: Use the color space and
transfer matrix that was set in
the menu.
[ITU-R BT.709]
[EBU]
[SMPTE-C]
[Native]
[S-Gamut/S-Gamut3]
[S-Gamut3.Cine]
[DCI-P3]
[ITU-R BT.2020]
[ITU-R BT.709]
[ITU-R BT.2020]
Submenu
Setting
[EOTF]
Select the gamma from the following:
[2.2]
[2.4]
[2.6]
[CRT]
[2.4(HDR)]
[S-Log3(HDR)]
[S-Log2(HDR)]
[SMPTE ST 2084(HDR)]
[HLG SG 1.2(HDR)]
[HLG SG Variable(HDR)]
1) The unit corresponds to the HLG
(Hybrid Log-Gamma). Refer to
"HLG specification" (page 29).
When [HLG SG Variable(HDR)] is
selected
[HLG System Gamma]: Sets the
system gamma of the HLG. Set
from 1.000 to 1.500.
Note
The HDR display is a method to
faithfully display the brightness of
signals defined of 100% or more level
without compressing the brightness
parts.
You can check the bright portions
exceeding the displayable brightness
of the unit by decreasing the
contrast.
In the HDR display, the screen saver
is forcibly set. [Off] cannot be
selected.
In the HDR display, [Flicker Free] is
forcibly set. [Off] cannot be selected.
Using the unit with the high
brightness display for extended
periods may cause eyestrain or
reduction of eyesight. Be sure to take
an occasional break when using.
Follow RECOMMENDATION ITU-
R BT.1702 "Guidance for the
reduction of photosensitive epileptic
seizures caused by television" or
other guidelines to use.
In the HDR display, the display
surface may emit heat when high
brightness images are output. Do not
touch the surface.
Do not display static images that
contains high brightness display,
time codes, markers, or logos for
extended periods to reduce the risk
of burn-in. Consider to apply a
displaying method with a low level
signals of 100% or less.
1)
1)
Advertisement
Table of Contents
