JUKI SC-920 Instruction Manual page 29

No. Item
Pedal curve is selected. (Improving pedal inching operation)
87 Function of pedal
curve selection
Number of rotations
Automatic UP stop function is set immediately after turning ON the
90 Initial motion up
power.
stop function
0 : off
1 : on
91 Function of prohibiting It is effective in combination with the machine head provided
compensation with tension release function.
operation after turning 0 : Tension release function is ineffective.
handwheel by hand 1 : Tension release function is effective.
92 Function of Function to reduce speed at the time of completion of reverse
reducing speed feed stitching at the start of sewing.
of reverse feed 0 : Speed is not reduced.
stitching at the 1 : Speed is reduced.
start of sewing
93 Function added to Operation of needle up/down compensating switch is changed
needle up/down after turning ON the power or thread trimming.
compensating 0 : Normal (needle up/down compensating stitching only)
switch 1 : One stitch compensating stitching is performed only when
94 Continuous + The function that does not stop the sewing machine by com-
One-shot nonstop bining continuous stitching with one-shot stitching using the
function
program sewing function which is available in the IP operation
panel.
0 : Normal (The sewing machine stops when a step is com-
1 : The sewing machine does not stop when a step is com-
95 Head selection Machine head to be used is selected.
function (When the machine head is changed, each setting item is changed
to the initial value of the machine head.)
96 Max. number of Max. number of rotation of the sewing machine head can be set.
rotation setting
(The MAX value differs by machine head.)
100 Number of Sets the number of stitches to be sewn at the beginning of sew-
stitches sewn
ing before the thread clamp solenoid (CN36-7) starts operating
before thread
0: Thread clamp solenoid does not operate.
clamp works at
1-9: The number of stitches to be sewn before the thread clamp
the beginning of
solenoid operates
sewing
103 Needle cooler Delay time from the stop of sewing machine to the output OFF is
output OFF specified using the needle cooler output function.
delay time
120 Main shaft Main shaft reference angle is compensated.
reference angle
compensation
121 Up position Angle to detect UP position starting is compensated.
starting angle
compensation
122 DOWN position Angle to detect DOWN position starting is compensated.
starting angle
compensation
124 Setting of Setting to reduce the power consumption while the sewing ma-
energy-saving chine is in standby state
function during 0: Energy-saving mode is ineffective
standby 1: Energy-saving mode is effective
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
Description
2
0
aforementioned changeover is made. (Upper stop / upper
stop)
pleted.)
pleted and proceeds to next step.
Setting range
0/1/2
1
Pedal stroke
0/1
0/1
0/1
0/1
0/1
150 to MAX
(sti/min)
0-9
(stitches)
100 to
2000 (ms)
–60 to 60
–15 to 15
–15 to 15
0/1
– 27 –
Indication of function setting Ref. page
8 7 0
36
9 0 1
37
9 1 1
9 2 0
36
9 3 0
37
9 4 0
37
9 5 d L b M
9 6 4 0 0 0
37
1 0 0 0
1 0 3 5 0 0
1 2 0 – 2 3
37
1 2 1 5
37
1 2 2 0
37
1 2 4 0
37