Umid Information Display - Panasonic AJ-SD965 Operating Instructions Manual

Error messages
$ Displaying the "HOURS METER"
information
Turn the search dial to move the cursor (2).
The description for the item where the cursor is located
is shown on the counter display.
No./Item
Ser Displays the unit's serial No.
222222222
H00 Displays the time that the power has been
supplied in one-hour units.
OPERATION
H01 Displays the time that the drum has been
rotating in one-hour units.
DRUM RUN
H02 Displays the time that the tape has been running
during FF, REW, PLAY, SEARCH (JOG, SLOW,
TAPE RUN SHTL), REC, and EDIT modes (except for
STILL in the JOG, SLOW or SHTL mode) in
one-hour units.
H03 The number of times for threading (loading)/
unthreading (unloading) is displayed in single
THREADING units.
H04 Displays the number of times front loading has
been performed in single units.
F LOADING
H05 Displays the time that the LCD monitor has been
lighting in one-hour units.
LCD ON
H11 Displays the time that the drum has been
rotating in one-hour units. (Can be reset)
DRUM RUNr
H12 Displays the time that the tape has been running
during FF, REW, PLAY, SEARCH (JOG, SLOW,
TAPE RUNr SHTL), REC, and EDIT modes (except for
STILL in the JOG, SLOW or SHTL mode) in
one-hour units. (Can be reset)
H13 The number of times for threading (loading)/
unthreading (unloading) is displayed in single
THREADINGr units. (Can be reset)
H14 Displays the number of times front loading has
been performed in single units.
F LOADINGr (Can be reset)
H15 Displays the time that the LCD monitor has been
lighting in one-hour units.
LCD ONr (Can be reset)
H30 The number of times the power has been turned
on is displayed in single units.
POWER ON
<Notes>
O The resettable items in the "HOURS METER"
information are reset by the shop when performing
maintenance or other work.
O The search buttons and the search dial cannot be
operated while the DIAG menu is displayed.
72
(continued)
Description
If "T&S&M" is selected in the setup menu No. 008
(DISPLAY SEL), a message appears in the mode
display whenever a warning or error occurs. When
multiple events occur, the event with the highest
priority is displayed.
Priority
High Error messages (See error message table)
When an operational malfunction has occurred in the
unit, the error number flashes and the error message
is indicated on the counter display.
INT SG
When SG has been selected as the input signal with
the INPUT SELECT buttons, pressing the REC
button or the EDIT button (E-E mode) will display
"INT SG" for the first two seconds.
This is also displayed for the first two seconds when
starting editing.
NO INPUT
If there is no input signal (except for analog audio) to
the connector selected using the INPUT SELECT
buttons, pressing the REC button or the EDIT button
(E-E mode) will display "NO INPUT" for the first two
seconds.
This is also displayed for the first two seconds when
starting editing.
Warning messages (See error message table)
When a warning occurs in this unit, the error number
and warning message are indicated on the counter
display.
When multiple warnings occur, the warning with the
Low
highest priority is displayed.

$ UMID information display

This is displayed when UMID information is present on
the input signal in E-E mode.
This lamp lights during tape playback when UMID
information has been recorded on the tape.
"NO-INFO" is displayed when there is no UMID
information.
Item
MATNO Material number
COPY Instance number (No. of copies)
OWNR Country, organization, user
POS Reception status from GPS satellites when
recording spatial coordinates (height above sea
level, longitude and latitude):
HOLD: No reception from any satellite
2D: Reception possible, but number of
satellites is insufficient. Height above
sea level will not be accurate.
3D: Good reception
DATE Date
TIME UTC (Coordinated Universal Time) and time
difference with UTC
Display/Description
Display/Description