Program Mode; Function Keys; Setting The Lcd Contrast; Daylight Saving Time Setting - La Crosse WS-9065U Instruction Manual

into the remote temperature sensor first. The time will show -:—
and start searching for the signal. If it successfully receives the
time signal (usually at night), it will display the correct time (default
time-zone is Eastern).You will need to adjust the time zone to
match your local time.

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or the CH
button is pressed during the programming mode, the unit will
confirm/set the last information entered-the display will stop
flashing and return to normal time-date readings. If you don't leave
the program mode during the programming of sections IV through
XI, you can advance to step 4 of the next program setting. If you
do leave the program setting (or want to program a specific setting)
follow each instructional step to program that setting.
I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS
The programming sequence and default (factory) settings are as
follows:
LCD Contrast
Time Zone
Daylight Saving Time
Radio-controlled time reception
12/24-hour time
Time
Year
Day and Month
Snooze (this function not used)
Temperature Format
Forecast Sensitivity
Please note that while there is a snooze adjustment in the
programming this is an unused function as there is no alarm on
the indoor weather station.
II. FUNCTION KEYS
The function keys are located on the front of the unit directly below
the LCD.
GB
P.6
6. Press and release the SET button to confirm and advance to
the Daylight Saving Time setting.
V. DAYLIGHT SAVING TIME (DST) SETTING
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
flash.
3. Press and release the SET button twice.
4. "DST" will appear in the date LCD and either "1" or "0" will
flash.
DATE
5. Press and release the IN button to select DST on or off.
"DST 0" indicates that the feature is off and the WWVB will not
change times automatically. "DST 1" indicates that the feature is
on and the WWVB will change times automatically.
Note: Some locations (Arizona and parts of Indiana) do not follow
Daylight Saving Time, and should select "DST 0."
6. Press and release the SET button to confirm and advance to
the radio-controlled time on/off setting.
VI. RADIO-CONTROLLED TIME ON/OFF SETTING
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
flash.
3. Press and release the SET button three times.
4. "RCC" will appear in the date LCD and "ON" or "OFF" will flash
in the time LCD.
5. Press and release the IN button to select radio-controlled time
on or off.
6. Press and release the SET button to confirm and advance to
the 12/24-hour time setting.
VII. 12 OR 24 HOUR TIME SETTING
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
flash.
3. Press and release the SET button four times.
4. "12h" or "24h" will flash in the time LCD.
GB
P.8
III. SETTING THE LCD CONTRAST
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
Note: There are 8 LCD contrast levels to choose from-"Lcd 0" is
the lightest, and "Lcd 7" is the darkest.
3. Press and release the IN button to select the level you desire.
4. Press and release the SET button to confirm and advance to
IV. TIME ZONE SETTING
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
5
3. Press and release the SET button again.
-5 (Eastern)
4. The time zone will flash in the date LCD.
1 (on)
ON
12
12:00
2003
1.1.
5. Press and release the IN button to select your time zone.
10
˚F Note: When a time zone for the U.S. is selected the corresponding
2
abbreviation will appear above the time (please see the table on
the next page). It is possible to select any time zone from -12
GMT to +12 GMT (for example to see the time in another country)
5. Press and release the IN button to select 12 or 24-hour time
Note: When in the 12-hour format "P.M" will appear to the left of
the hour in the time LCD between the hours of noon and midnight.
6. Press and release the SET button to confirm and advance to
VIII. TIME SETTING
There are two methods by which the time and date can be set:
A) Automatically via WWVB reception, or
B) Manually.
A. WWVB (Remote Control Time)
This method requires you to do nothing, except wait for the signal
to be received, and to select a time zone. Reception usually takes
approximately 10 minutes during optimal conditions. The best
condition for reception is at night, between midnight and 6:00 am-
when there is less atmospheric interference. To keep your time
as accurate as possible, the indoor weather station conducts a
WWVB search every night between these hours, and overrides
any manually set time. The WWVB tower icon (appearing in the
TIME LCD) will flash when a signal-search is in progress and a
signal is being received, and will remain steady when the signal
has been received. If the WWVB time has not been received after
10 minutes of battery installation, you may manually set the time
or leave the time function alone (reception will occur regardless).
B. MANUAL TIME SETTING
Note: When in the 12-hour format "P.M" will appear to the left of
the hour in the time LCD between the hours of noon and midnight.
1. Press and hold the SET button for 5 seconds.
2. "LCD" will show in the time LCD and the number setting will
3. Press and release the SET button five times.
4. The time will flash in the time LCD.
flash.
TIME
the Time Zone setting.
flash.
DATE
TIME ZONES
GMT 0
Atlantic -4
EST; Eastern -5
CST; Central -6
MST; Mountain -7
PST; Pacific -8
ALA; Alaska -9
HAW; Hawaii -10
TIME
format.
the time setting.
flash.
TIME EST
GB
P.7
GB
P.9