Mounting Instructions - Pacific PV-12 Operating & Maintenance Instructions

ITEM PART NO. DESCRIPTION
1 960008 Bolt, Shoulder
2 609703 Wheel
3 608506 Squeegee Channel Weldment
4 920019 Nut, 1/4-20 Hex Jam
5 W189D Screw, 14-20x3/4 HH CS
6 A13018 Knob
7 W506D Screw,5/16-18x3/4 HH MS
8 W380D Screw, 10-32x3/4 PHP
9 607209 Retainer-Squeegee Blade
10 600705 Blade, 28" Squeegee
11 600301 Arm Weldment-Squeegee
12 980006 Washer, 5/16 Lock
13 920001 Nut, 10-32 Elastic Stop
14 980007 Washer, 5/16 Flat
For the Models PV-18S/Gulper 18PS which include the
Squeegee Assembly:
1. Position the machine on a level surface.
2. Unlock the lower squeegee lift arm weldment (11).
3. Align the squeegee with the lift arm weldment; using the
shoulder screws (5) on the back side of the lift arm
weldment, place the jam nuts (4) between the arm weldment
and squeegee and then screw the knobs (6) on the front of
the squeegee assembly. Leave the hardware slightly loose.
4. Position the squeegee assembly to assure that it sits flat
from side to side level with the surface. Then tighten the
knobs.
5. Connect the vacuum hose assembly, Items 17, 18 and 19
to the tank adaptor and squeegee adaptor.
6. Adjust the squeegee height by rotating the screw (27)
clockwise to lower the squeegee and counterclockwise to
raise the squeegee.
Squeegee Assembly as an Accessory - for the Models PV-
12/Gulper 12P, PV-18/Gulper 18P and PV-18D/Gulper
18PD:
1. Remove the head assembly and the filter bag assembly.
2. Turn the machine upside down.
3. Mount the arm support brackets (16) to the inner surface
of the squeegee lift arm weldment (11) using the shoulder
screws (15), flat washers (14) and jam nut (20). Reference
the illustration - two washers are on the outside of the lift
arm weldment and one washer is between the support
bracket and squeegee lift arm weldment. Tighten the hard-
ware and check for free rotation. If needed, slightly loosen
the jam nut.
SQUEEGEE ASSEMBLY
PART #608521
QTY. ITEM PART NO. DESCRIPTION
2 15
2 16
1 17
3 18
2 19
2 20
6 21
16 22
2 23
2 24
1 25
6 26
2 27
6

MOUNTING INSTRUCTIONS

4.
5.
6.
7.
8.
9.
10. Turn the machine upright.
11. Proceed with steps 1-4 from the previous section.
12. If using on a PV-12/12P remove the adaptor (17) and cut
13. Screw adaptor (17) onto the hose assembly.
14. Connect the vacuum hose assembly, Items 17, 18 and 19
15. Adjust the squeegee height by rotating the screw (27)
16. Replace the head assembly and filter bag assembly.
11
960007 Bolt, Shoulder, 3/8x1/2 Lg
600806 Bracket, Arm Support
600205 Adaptor, Hose
604106 Hose, Vacuum
600206 Adaptor, Hose
920012 Nut, 5/16-18 ESNA Lock
962015 Screw, 10-32x3/8 Pan Hd
608507 Support, Lock Backup
605102 Lock, Squeegee Spring
608201 Spacer, Squeegee Support
608512 Stop, Squeegee Arm
W168D Screw, Set
962010 Screw, 1/4-20x1 HHCS
Mount the squeegee arm stop (25) to the lift arm weldment
(11) using the set screw (26). Then assemble the screw
(27) and nut (4) to the stop (25) as illustrated.
Position this assembly on the bottom of the tank with the
foot pedal to the rear of the tank, facing down.
Attach the arm support brackets (16) and the spacers (24)
to the tank with the bolt (7) and washer (12).
Assemble the lock backup support (22) to the lock spring
(23) with the screw (21) and nut (13) keeping the edges
flush.
Attach the spring lock assembly (22&23) to the bottom of
the tank using the bolt (7) and washer (12).
With the spring lock pressed in against the tank, check
that the pedal clears the spring lock. Loosen the bolt (7)
to adjust the spring lock assembly (22&23) location.
the hose assembly (18&19) to a 16 inch length. The 16
inches includes the adaptor (19). Do not cut the hose
assembly for the PV-18/18P and PV-18D/18PD.
to the tank adaptor and squeegee adaptor.
clockwise to lower the squeegee and counterclockwise to
raise the squeegee.
QTY.
2
2
1
1
1
4
2
1
1
2
1
1
1