Speaker Installation Options - Panasonic SC-HT743 Operating Instructions Manual

Speaker installation options

∫ Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached should be
capable of supporting over 10 kg (22 lbs) [[HT940] 15 kg (33 lbs)
for the front speakers] per screw. Consult a qualified building
contractor when attaching the speakers to a wall. Improper
attachment may result in damage to the wall and speakers.
≥ When mounting the front speakers to a wall, we recommend using
a string (not included) to prevent it from falling.
2 Screws [HT740]
Preparation for front speakers
[HT740] [HT743]
1 Remove the speaker cable from the stand.
2 Connect the cable (➜ page 4).
[HT940]
1 Pull down the longer part
of the cable to release
the cable from the groove
inside the stand, and
then pull the speaker cable out from the stand.
2 Feed the cable into the bottom of the
speaker and through the slot at the rear.
3 Connect the cable (➜ page 5).
1 [HT740] [HT743]
Attach the cover plate to the front speaker.
Cover plate
2 Drive a screw (not included) into the wall.
‰4.0 mm (
5
Wall or pillar
3 Fit the speaker securely onto the screw(s) with the hole(s).
Front speaker [HT740]
106 mm
z)
3
(4 /
16
6
[HT743] 2 Cover plates [HT740]
Release the cable
from the groove.
Screw
Tighten securely.
‰7.5 to 9.5 mm
q)
/
32
q to
19
( /
64
5.0 to 7.0 mm (
[HT743] Center speaker [HT740]
200 mm
(7 7 /
8
340 mm
z)
(13 3 /
8 Surround speaker [HT740]
Front speaker [HT940]
255 mm
z)
(10 1 /
16
[HT743]
e.g.
Reattaching the speaker cable to the stand
[HT740] [HT743]
1 Remove the eight screws
from the stand, and remove
the speaker net.
2 Position the cable.
3 Attach the speaker net with the screws.
[HT940]
1 Remove the two screws from the stand, and remove the metal cover.
2 Pull the cable out about 40 cm (15
cover, and insert the plastic cover.
Approx. 40 cm (15
3 Insert the metal cover
so it does not disturb
q)
3
/
8 the cable and close
tightly with the two screws.
q to q)
3 / 9 /
16 32
∫ Fitting speaker stands
(Except front speakers)
Ensure the stands meet these conditions before purchasing them.
[HT743]
Note the diameter and length of the screws and the distance
between screws as shown in the diagram.
≥ The stands must be able to support over 10 kg (22 lbs).
≥ The stands must be stable even if the speakers are in a high position.
e.g. Center speaker [HT740]
z)
Metal screw holes
For attaching to speaker
stands
[HT743]
5 mm (
Plate thickness plus 7 mm
to 10 mm (plus
Center speaker [HT940]
Surround speaker [HT940]
320 mm
z)
19
(12 /
32
In this position, the
speaker will likely
fall if moved to the
left or right.
Press the cable into
the groove.
Approx.
Cable
15 cm
z)
(5 29 /
32
Screw
Metal cover
Plastic cover
z) from the hole in the metal
3 /
4
z)
3 /
4
(not included)
[HT743]
q), pitch 0.8 mm ( q)
3 / 1 /
16 32
q to q)
9 / 13 /
60 mm (2
32 32
Speaker stand (not included)
190 mm
z)
15
(7 /
32
Move the speaker
so that the screw
is in this position.
Screw
Screw
q)
3 /
8