Hakko Electronics FR-410 Instruction Manual
Desoldering station
Hide thumbs
Also See for FR-410:
- Instruction manual (36 pages) ,
- Quick start manual (4 pages) ,
- Instruction manual (36 pages)
Advertisement
Instruction Manual
Thank you for purchasing the HAKKO FR-410 Desoldering Tool.
Please read this manual before operating the HAKKO FR-410.
Keep this manual readily accessible for reference.
1.
Desoldering Tool
(HAKKO FR-4101)
●
●
Table of Contents
................................................. 1
...................................................... 3
.......................................................... 4
........................................ 7
..................................................... 8
...................... 1
................. 2
...........................11
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hakko Electronics FR-410
Summary of Contents for Hakko Electronics FR-410
-
Page 1: Table Of Contents
Desoldering Tool (HAKKO FR-4101) Instruction Manual ● Thank you for purchasing the HAKKO FR-410 Desoldering Tool. Please read this manual before operating the HAKKO FR-410. Keep this manual readily accessible for reference. ● Table of Contents PACKING LIST AND PART NAMES ...... -
Page 2: Packing List And Part Names
1. PACKING LIST AND PART NAMES Please check to make sure that all items listed below are included in the package. HAKKO FR-410 Desoldering station HAKKO FH-410 Handpiece holder HAKKO FR-4101 Desoldering Handpiece Tool box with N61-05 (ø1.0mm [0.04 in]) nozzle... -
Page 3: Warnings, Cautions And Notes
● Use only genuine HAKKO replacement parts. ● Do not allow the HAKKO FR-410 to become wet, or use it when hands are wet. ● Be sure to hold the plug when inserting or removing the handpiece and power cords. -
Page 4: Initial Setup
4. INITIAL SETUP A. Handpiece holder Loosen the adjusting screws to change the angle of the handpiece receptacle as you like, then tighten the screws. CAUTION Increasing the angle of the handpiece receptacle will cause an increase in the handpiece temperature. ●... -
Page 5: Operation
To disconnect, pull the plug 2. Connect the plug from the HAKKO FR-4101 from the receptacle while to the receptacle on the HAKKO FR-410. pressing down the tab on the plug. CAUTION Connect the plug to the receptacle, aligning the tab on the plug with the opening on the receptacle. - Page 6 Please wait for the heater to reach the set temperature. B. Making Changes to Settings ● Selecting the preset number The HAKKO FR-410 has a preset mode. 1. Press any of the three control buttons. 2. The preset selection screen appears.
- Page 7 3. Make your SELECTION by moving the cursor UP or DOWN 4. Press the <ENT> button to by pressing the corresponding finalize your selection. buttons. PRESET1 350℃ PRESET1 350℃ PRESET2 400℃ PRESET2 400℃ PRESET3 450℃ PRESET3 450℃ <↑> <↓> <ENT> <↑>...
-
Page 8: Parameter Setting
3. Make your SELECTION by moving the cursor UP or DOWN 4. Press the <ENT> button to by pressing the corresponding finalize your selection. buttons. Set Temp Set Temp Offset Temp Offset Temp Vacuum Check Vacuum Check <↑> <↓> <ENT> <↑>... -
Page 9: Maintenance
7. MAINTENANCE Properly maintained, the HAKKO FR-410 desoldering tool should provide years of good service. Efficient desoldering depends upon the temperature, nozzle selection, and proper routine maintenance. Perform the following service procedures as dictated by the conditions of the station's usage. - Page 10 Nozzle Maintenance CAUTION The desoldering tool may be extremely hot. During maintenance, please work carefully. 1. Inspect and clean the nozzle ● Turn the power switch ON and let the nozzle Cleaning with the nozzle cleaning pin heat up. The cleaning pin passes completely through the CAUTION hole.
- Page 11 2. Disassemble the heating element. Remove the element cover assembly and the nozzle with the provided wrench. CAUTION The element cover assembly is held to The heating element is the nozzle changing very hot during operation. tool by pressing this part from both sides.
-
Page 12: Trouble Shooting Guide
8. TROUBLE SHOOTING GUIDE WARNING Before checking the inside of the HAKKO FR-410 or replacing parts, be sure to disconnect the power plug. Failure to do so may result in electric shock. ● Display does not turn CHECK Is the power supply cable or connection plug disconnected? ACTION : Connect it tightly.
Need help?
Do you have a question about the FR-410 and is the answer not in the manual?
Questions and answers