Adding, Changing Or Deleting A User Code - CDVI KCIN Installation Manual

INSTALLATION MANUAL
KCIN
Illuminated weatherproof Keypad with Remote Electronics - 2 or 3 relays
Default values Audible signal:
- Without codes. The buzzer indicates different audible
- Illumination time: 10 seconds. signals. It can be turned off by cutting
- Relay release time: 1 second. the ST1 wire on the remote controller
- Code length: 5-digit. 1 short beep: Keypad powered
- Master Code: 1 2 3 4 5. 1 long beep: Data computing
- Programming security time : in programming or access granted
120 secondes. 2 short beeps: Enter or Exit
- Code length for sub master code: from programming
Version 1 relay (Group 1) = 4 short beeps:
A and B, Data computing error.
Version 2 relays (Group 2) =
Code length
1 and 3
The master code and the User codes
Version 3 relays (Group 3) =
can be of 4 or 5-digit in length.
4 and 6.
All the keypad keys can be used
to program a code. The master code
A. RESET MASTER CODE
AND USER CODES
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A6 to reset the Master Code
and the User codes.
One beep is emitted. Press on A
and B to confirm reset of all memory
of the keypad. Wait for two beeps.
The master code is restored
to its default value 1 2 3 4 5
and all the User codes are deleted
from the keypad. Once the reset
is completed then the keypad returns
to a stand-by operating mode.
OR
1. Cut the power. Put the jumper on P2.
2. Put the power back.
Wait approximately 3 seconds.
Two beeps are emitted to confirm reset
of the keypad. Remove P2 jumper.
The master code is restored to its default
value 1 2 3 4 5 and all the User codes
are deleted from the keypad.
B. SETTING CODE LENGTH
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
6 6
cdvigroup.com
EN
and the Pin code can be of 4 or 5-digit
code. The master code CAN NOT
be used as a PIN code (User Pin code).
The master code CAN NOT be used
as a PIN code (User Pin code).
To delete a specific User pin Code replace
it by 0000 if code length is 4-digit format
or replace it by 00000 if the code
is in 5-digit format.
P2 jumper:
Reset master code and user codes
P3 jumper:
modification of individual
code by the user
2. Press A4 to program the code length.
One beep is emitted. Press 4 or 5
for the digit code. One beep is emitted
to confirm programming of the code length.
3. Press A5 to modify the master code.
One beep is emitted. Enter the new 4
or 5-digit master code. One beep is
emitted to confirm programming
of the new master code.
4. Press B to exit from
programming mode.
2 beeps are emitted to confirm that the key-
pad is in stand-by operating mode.
4 beeps indicate a data computing error.
C. CHANGING THE MASTER CODE
The master code is used only
to enter in programming mode.
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A5 to modify the master code.
One beep is emitted. Enter the new 4
or 5 digit master code. One beep
is emitted to confirm that the master
code is programmed.
3. Press B to exit from
the programming mode.
2 beeps are emitted to confirm that the key-
pad is in stand-by operating mode.
INSTALLATION MANUAL
KCIN
Illuminated weatherproof Keypad with Remote Electronics - 2 or 3 relays
D. ADDING, CHANGING
OR DELETING A USER CODE
Group 1: From address 00 to address 99,
relay output 1
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm entry
in programming mode.
2. To add a user code, enter the user
location (from 00 to 99).
If the user location is free 1 beep
is emitted, enter the 4 or 5-digit
User code.
3. To change a user code enter
the user location.
4 beeps are emitted to indicate that
user location is already programmed.
Enter a new 4 or 5-digit code.
A beep is emitted to confirm the new
user code.
4. To delete a User code enter
the user location.
4 beeps are emitted.
Press 0 0 0 0 0 in 5-digit length code
or 0 0 0 0 in 4-digit length code.
A beep is emitted to confirm the new
user code.
NOTE: If the Pin code is already programmed
or is identical to the master code,
then 4 beeps are emitted.
Press B to exit from the programming
mode. 2 beeps are emitted to confirm
that the keypad is in stand-by
operating mode.
E. TIME OUTPUTS
This section allows to program
the illumination time and the Relay
activation time.
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm
entry in programming mode.
2. Press A0 to program the key-in
keypad time and the keys lit time.
1 beep is emitted. Enter the time in 10th
of second – 10 for 10 seconds up to 99
for 99 seconds the backlighting dims
10 seconds after the last keypress
or switches off after entering a valid
code. Press 00 for permanent
EN
illumination keys.
One beep is emitted to validate the time.
3. Press A1 to program relay 1
output time (door release time).
1 beep is emitted. For a latched output
enter the time in seconds – 01 for 1
second up to 99 for 99 seconds.
Press 00 for a toggled output.
One beep is emitted to validate the time.
4. Press B to exit from
programming mode.
2 beeps are emitted to confirm that the key-
pad is in stand-by operating mode.
4 beeps indicate a data computing error.
F. RESET MASTER CODE
On stand-by operating mode,
put a jumper on P2.
Wait 1 second and then remove
the jumper. One beep is emitted.
The master code is restored
to its default value 1 2 3 4 5 in 5-digit
code and 1 2 3 4 in 4-digit code.
G. CHANGING THE CODE
BY A USER
To authorize a user to modify its own
User code put a jumper on P3
(to disable the feature remove the jumper).
1. Enter the old user code.
The relay is activated and a beep
is emitted.
2. Enter the 2-digit sub master code
(default sub master code A and B).
A beep is emitted to authorise
the modification.
3. Enter the new user code.
2 beeps are emitted to confirm
the new code.
4. Check the new user code to be sure
of the modification.
H. SETTING A SUB MASTER CODE
The Sub Master code allows the user
to change its own code without entering
in programming mode. For security
reasons the code need to be changed
periodically. This feature makes it easier
cdvigroup.com
7 7