Related Manuals for REMKO MALAGA Series ML 260
Summary of Contents for REMKO MALAGA Series ML 260
-
Page 1: Spare Parts
REMKO ML 260 to 680 Air-conditioning packets Wall units MALAGA series Operation Technology Spare Parts REMKO – powerful like a bear. Edition GB – R05... -
Page 3: Table Of Contents
Our guarantee becomes null and void if the unit is used, set up or maintained improperly, or if modifications are made to the supplied unit without our prior consent. Subject to changes! Air-conditioning packets Wall units REMKO ML 260 / 350 / 520 / 680 MALAGA series Contents Contents Page... -
Page 4: Safety Instructions
The REMKO ML 260 to 680 air-conditioners have a Never operate the units in rooms susceptible to ex- REMKO ML ...-AT outdoor unit designed for wall or floor plosions. The units are also not suitable for opera- installation outside and an ML ...-IT indoor unit de- tion in rooms containing large amounts of dust or ag- signed for upper wall installation inside. -
Page 5: Operation
Operation button Two to four seconds after the indoor unit has been con- This button is used to increase the temperature up nected to the power supply, operation can begin. to a maximum of 31°C. 4 Mode button Inserting the batteries into the remote control The operating mode is selected with this button. - Page 6 Button functionality The following settings can be made using the remote control at a distance of no more than 7m. Point the remote control at the receiver on the right side of the indoor unit. The unit beeps to confirm that a button has been pressed and the signal has been correctly received.
- Page 7 Use the MODE button to select the individual operating modes. There are 4 modes Mode button available: 1. Automatic, automatic selection of cooling or heating mode 2. Cooling, operating mode primarily for summer 3. Dehumidifying, summer or winter operating mode 4.
- Page 8 The air outlet fins are individually set with this button. You can select 5 positions and an os- Fin button cillating function. Functional process The oscillating function of the air outlet fins is set with this button. This enables you to im- Swing button mediately switch between a set position and the oscillating function.
-
Page 9: Shutting Down The Unit
Shutting Down the Unit LED display on the indoor unit Temporary shutdown 1. Let the unit run in cool mode for 30 minutes at a temperature setting of 31°C. POWER On / Off (red) 2. Switch the indoor unit off using the remote control. PROTECT Compressor protection (green) 3. -
Page 10: Maintenance And Service
Maintenance and Service Before any work on the units is performed, they must be disconnected from the power supply and secured against being inadvertently switched on! Regular care and the observation of a number of basic rules will ensure the unit’s long service life and reliable operation. -
Page 11: Troubleshooting
Is the collector filled with water and Have pump checked by authorised service float regulator is defective the pump is not working? centre Should the unit still not work after performing these functional checks, please contact the closest dealer or REMKO GmbH & Co KG. directly. -
Page 12: Technical Data
Technical Data ML 260 ML 350 ML 520 ML 680 Nominal cooling capacity* 2.59 3.50 5.27 6.80 Energy efficiency class cooling Energy efficiency ratio 2.82 2.82 2.61 2.61 Power consumption in 500 hours 1010 1305 Operational area ( ), approx. m³... -
Page 13: Dimensions
Dimensions ML 260 AT ML 260 IT ML 350 AT ML 350 IT ML 520 IT ML 520 AT 1096 ML 680 IT ML 680 AT 1096... -
Page 14: Assembly Instructions For Service Personnel
Assembly Instructions for Service Personnel Important instructions prior to installation The indoor unit and outdoor unit of the REMKO air- Ensure that the contents of the package are com- conditioner have been adjusted to one another from plete and that the units have no visible damage re- a technical standpoint. - Page 15 Snow: Setup locations for the outdoor unit The unit must be set up on a surface that is level, The unit should be installed on the wall in areas with smooth and solid. The unit must also be secured heavy snowfall. against tipping over.
- Page 16 Refrigerant 1500 injection pipe Dimensions in mm If REMKO refrigerant pipes are used, the electrical control line and the condensation pipe must be pro- vided by the customer. Attaching the wall mount Therefore, the lead-through to be created must be...
-
Page 17: Installation
Installation The following instructions describe the installation of the 10. If, due to structural design conditions, it is not possi- cooling cycle and the assembly of the indoor and outdoor ble to guide the condensation pipe through as well, unit. make sure that the condensation can drain freely at all times. -
Page 18: Impermeability Check
Electrical Connection Oil recirculation If the outdoor unit is set up at a higher level than the in- All electrical installations may only be performed by door unit, appropriate steps must be taken for oil recir- authorised service centres in line with the relevant regula- culation. -
Page 19: Wiring Diagram
Connecting the outdoor unit If the unit is being operated at outside temperatures be- Prior to installing the connection, observed the follow- low 0°C, the pipes must be placed in such a way that ing: they are protected from frost. The customer must install the con- Always use suitable hose clips. -
Page 20: Adding Refrigerant
"guarantee certificate" After all components have been connected and enclosed with all units and send it back to REMKO GmbH checked, the system can be put into operation. & Co. KG... -
Page 21: Environment And Recycling
Environment und Recycling Important information about recycling! Only authorised service centres may come into contact with the cooling cycle. This ensures that refrigerant does not escape into the environment when the unit is being repaired. Both the refrigerant and the system parts are subject to special requirements for disposal. -
Page 22: Certification For Initial Operation
Certification for Initial Operation Date 01/2005 Subsequent Operation of a REMKO air-conditioning system Initial Operation Unit data Outdoor unit Indoor unit Type of unit Unit number Refrigerant pipe length/height ———– Oil elevation arcs ———– units Additional refrigerant amount ———– Condensation pump ———–... - Page 24 REMKO GmbH & Co. KG Air-Conditioning and Heating Technology D-32791 Lage Im Seelenkamp 12 • D-32777 Lage P.O. Box 1827 • Phone: +49 52 32 606 - 0 Fax: +49 52 32 606 - 260 E-mail: export@remko.de Internet: www.remko.de...