Related Manuals for REMKO MKT 291
Summary of Contents for REMKO MKT 291
- Page 1 Assembly and operating instructions REMKO MKT 291, MKT 291 S-Line Local Air Conditioner Read the instructions prior to performing any task! 0057-2014-01 Edition 2, en_GB...
- Page 2 Read these operating instructions carefully before commis- sioning / using this device! These instructions are an integral part of the system and must always be kept near or on the device. Subject to modifications; No liability accepted for errors or mis- prints! Installation and operating instructions (translation of the orig- inal)
-
Page 3: Table Of Contents
Table of contents Safety and usage instructions......................4 1.1 General safety notes........................4 1.2 Identification of notes........................4 1.3 Personnel qualifications........................4 1.4 Dangers of failure to observe the safety notes................4 1.5 Safety-conscious working....................... 4 1.6 Safety notes for the operator......................5 1.7 Safety notes for installation, maintenance and inspection.............. -
Page 4: Safety And Usage Instructions
REMKO MKT Safety and usage instructions CAUTION! This combination of symbol and signal word 1.1 General safety notes warns of a potentially hazardous situation, which if not avoided may cause injury or mate- Carefully read the operating manual before com- rial and environmental damage. -
Page 5: Safety Notes For The Operator
"certificate of warranty" to with all applicable regional regulations. REMKO GmbH & Co. KG at the time when the Local regulations and laws such as Water units are purchased and commissioned. -
Page 6: Transport And Packaging
REMKO MKT 1.11 Transport and packaging The devices are supplied in a sturdy shipping con- tainer. Please check the equipment immediately upon delivery and note any damage or missing parts on the delivery and inform the shipper and your contractual partner. For later complaints can not be guaranteed. -
Page 7: Technical Data
Technical data 2.1 Unit data Series MKT 291 MKT 291 Operating mode Local compact air conditioning unit for cooling 2,94 Nominal cooling output Energy efficiency ratio - cooling 2,61 Energy efficiency rating EER Energy consumption, hourly kWh/60 min 1,11 Approx. application area (room volume) m³... -
Page 8: Design And Function
REMKO MKT Design and function Unit description The local air conditioning unit is particularly well suited to flexible use. The local room air conditioner comprises a floor- standing unit for the indoor area and an exhaust air hose to conduct the heat away. The indoor unit... -
Page 9: Operation
Operation The system can be operated by means of the control panel on the unit or via the standard infrared remote controller. The functional operation of the keys among themselves is identical, however, the designation can vary. The batteries must be correctly inserted before the infrared remote control is used. Fig. - Page 10 REMKO MKT Cooling mode "Cool" Attach the exhaust air hose to a wall pass- through or window Switch the unit on with the "Power" key Press the "Mode" key until the "Cool" LED illuminates. Select the setting for the fan via the "Fan speed"...
-
Page 11: Assembly And Installation
Assembly and "Timer" installation You can switch the unit on and off automatically with the timer. The switch on delay or switch off Assembly and unit installation instructions delay can be programmed for this. The unit is positioned at the desired location with Automatic switch on the discharge side pointing into the room. - Page 12 REMKO MKT Check whether the stopper in the condensate Conduct the warm exhaust air away drain is present and correctly installed. There is a risk of uncontrolled condensate leakage after NOTICE! commissioning. The exhaust air hose should always be laid...
- Page 13 Via a wall pass-through Fig. 11: Exhaust air with tilted window The hose supplied is firmly attached to a wall pass- through. A suitable wall pass-through is available as an accessory (Fig. 12). Fig. 12: Wall pass-though NOTICE! Fig. 10: Exhaust air with open window In some circumstances routing the exhaust air via a firmly attached exhaust air hose, e.g.
- Page 14 REMKO MKT Installation scheme for wall pass-though (accessory) Fig. 13: Installation example 1: External grill 3: Non-return flap 2: Telescopic tube 4: Sealing cover Installation instructions Create a core hole in the exterior wall (max. wall thickness 480 mm) with a diameter of at least 135 mm.
-
Page 15: Electrical Wiring
Electrical wiring Electrical drawings A2517-160 Fig. 14: Electrical drawings Mains power circuit board Condenser fan Control panel control board Condensate motor Power plug Colour coding: Microswitch (reservoir) Brown Temperature sensor, recirculated air Blue Evaporator fan Compressor White We reserve the right to modify the dimensions and design as part of the ongoing technical development process... -
Page 16: Commissioning
REMKO MKT Commissioning Before every commissioning the air inlet and outlet openings should be checked for foreign bodies and the air inlet filter must be checked for dirt. Blocked or soiled grids and filters must be cleaned immedi- ately, see "Care and maintenance" chapter. -
Page 17: Troubleshooting And Customer Service
Troubleshooting and customer service The unit has been manufactured using state-of-the-art production methods and has been tested several times to ensure that it works properly. If malfunctions should occur, please check the unit as detailed in the list below. Please inform your dealer if the unit is still not working correctly after all the function checks have been performed. - Page 18 REMKO MKT Fault description Cause Remedy The unit does not cool prop- LED cooling indicator The "Cool" LED indicator must illuminate erly Close windows, doors, blinds and curtains Exhaust air hose Must be properly attached. It must not be kinked, sloping downwards or laid in bends that are too tight.
-
Page 19: Care And Maintenance
Care and maintenance Filter cleaning The unit is equipped with an air filter. This can be Regular care and observation of some basic points withdrawn from the rear of the unit. The filter must will ensure trouble-free operation and a long be cleaned at regular intervals. -
Page 20: Shutdown
Permanent shutdown The entire system should only be dismantled by a specialist firm familiar with all environmental aspects involved. REMKO GmbH & Co. KG or your sales partner will be pleased to provide details of refrigerant specialists in your area. -
Page 21: Exploded Views And Spare Parts Lists
Exploded views and spare parts lists 11.1 Exploded view of the unit Fig. 18: Exploded view We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 22: Spare Parts List
Spare parts list For ordering spare parts, please contact directly to the REMKO GmbH & Co. KG. All their device the accompanying part numbers can be found in the download area on www.remko.de IMPORTANT! To ensure the correct delivery of spare parts, please always the device type with the corresponding serial number (see type plate) No. - Page 23 No. Description MKT 291 MKT 291 Connection nozzle Window nozzle Condensate drain nozzle with stopper By request with the serial number Remote control Exhaust air hose cpl. (no. 29; 30; 31) Spare parts not illustrated Ambient air probe By request with the serial number...
-
Page 24: Index
REMKO MKT Index Dehumidifying mode ....10 Operating mode "Mode" ....10 Assembly . - Page 26 REMKO MKT...
- Page 28 SFlb Customer Service Our equipment operates precisely and reliably. However, in the event of a fault, REMKO customer service is quickly at the scene. Our comprehensive network of experienced dealers always guarantees quick and REMKO GmbH & Co. KG reliable service.