Table of Contents
Advertisement
REMOTE CONTROL FUNCTION
NO. & NAME
1.
Press this button to turn this unit on or
POWER
Into standby mode.
ON/STANDBY
2.
Press this button to choose one of the
SURR MODE
following surround modes: THEATER,
HALL, PASSTHRU, MOVIE, MUSIC
and ROOM.
3.
Press this button to set the brightness of
the front display.
DIMMER
When play 5.1 CH source, and while you
4.
DOLBY DIGITAL
are enjoying Stereo, press this button to
playback source in DOLBY DIGITAL.
When play 5.1 CH source, and while you
5.
DTS
are enjoying Stereo, press this button to
playback source in DTS.
6.
When receiving Analog/digital /PCM
PRO LOGIC IIx
signal or 2CH Pro Logic, turn on this
button then the playing is under analog
5.1CH state.
7.
When the input signal is PCM, pressing
this button, you will get DTS NEO 6
DTS NEO: 6
MUSIC or DTS NEO 6 CINEMA.
Push this button to turn on or off the
8.
SURR BACK
surround back output. And when surround
back output is off, the DTS NEO:6 is
activated.
9.
Press this button to turn on/off the output
SUB ON/OFF
of subwoofer.
Press this button to select the 6.1
10.
DIRECT IN
analogue input.
11.
To select input modes: ANA, OPT, and
INPUT MODE
COAX when using digital in.
12.
Press this button to mute the sound, push
again to cancel the mute function.
MUTE
13/24.
Press these buttons to decrease or increase
the volume.
VOL. +/-
Allocates and memorizes radio stations
14.
APS
automatically.
15/25.
Press this button to select source upward
or downward.
SOURCE SEL
Press this button to alternate between
16.
ST/MONO
Stereo and Mono mode when listen to FM
broadcast.
17.
Press this button to alternate between FM
BAND
and AM.
DESCRIPTION
NO. & NAME
18.
These buttons are used to select a preset
NUMERIC
channel during the tuner mode.
BUTTONS
19.
Tuner frequency up and down.
TUNING +/-
20.
This button is used to select AUTO or
MANUAL tuning in AM and FM mode.
AUTO /MANUAL
Press once to set to AUTO again for
MANUAL.
Press it to store the broadcast station as a
21.
MEMORY
preset.
In FM state, press this button, the current
22.
PTY
program type appears on the display, using
TUNING +/- to select the program type
you desire.
23.
Select channels by pushing this button,
CH SELECT
then use VOL. +/- buttons to balance
speakers.
26.
Under the Pro Logic 5.1CH or DTS 5.1CH
mode, press this button and adjust the
LFE TRIM
volume to set the Low Frequency output
level
Press this button repeatedly to reach your
27.
DYNAMIC
desired compression dynamic range.
28.
To balance speakers in Dolby Digital or
TEST TONE
Dolby Pro Logic mode.
Press this button to display the state of
29.
DISPLAY
input source. And when listening to the
FM broadcasting with RDS, press this
button to show PS, PTY, RT and RT.
30.
With this unit in STEREO mode, only
STEREO
Front Left & Front Right speakers and
Woofer have output.
31.
Under PRO LOGIC II or Digital state, it
can change the desired Speaker Setting
SPK SETUP
shown on the display.
32.
These buttons are used for SPK SETUP
+ / -
and DELAY TIME, Treble and Bass
adjustment.
Press this button to set the delay time for
33.
DELAY
the Dolby digital/Dolby Pro Logic modes.
34.
Press this button for Treble adjustment,
then press +/- key to adjust the level.
TREBLE
(Note: In Pro Logic II, Surround and
Digital 5.1 mode, no function.)
Press this button for Bass adjustment, then
35.
BASS
press +/- key to adjust the level. (Note: In
Pro Logic II, Surround and Digital 5.1
mode, no function.)
13
DESCRIPTION
Advertisement
Table of Contents
