Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ozito HTE-360
Summary of Contents for Ozito HTE-360
-
Page 2: Specifications
SPECIFICATIONS - MODEL NO. HTE-360 Motor: 450W Input: 230-240V ~ 50Hz No load speed: 1600min Blade length: 360mm Blade spacing: 14mm Weight (tool only): 2.25kg KNOW YOUR PRODUCT 1. Rear handle 5. Blade support rail 2. On/Off switch 6. Cutting blade 3. -
Page 3: Table Of Contents
TABLE OF CONTENTS SPECIFICATIONS ……………………………………….. Page 2 INTRODUCTION………………………………………… Page 4 ELECTRICAL SAFETY…………….……………………… Page 4 GENERAL SAFETY WARNINGS………………………… Page 5 HEDGE TRIMMER SAFETY WARNINGS……………… Page 7 ASSEMBLY………………………………………………… Page 8 OPERATION……………………………………………… Page 9 MAINTENANCE…………….…………………………… Page 11 SPARE PARTS …………….……………………………... Page 12 DESCRIPTION OF SYMBOLS …………………………. Page 12 PACK CONTENTS ………………………………………... -
Page 4: Introduction
The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. -
Page 5: General Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 6 GENERAL POWER TOOL SAFETY WARNINGS d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 7: Hedge Trimmer Safety Warnings
HEDGE TRIMMER SAFETY WARNINGS • Keep all parts of the body away from the cutter blade. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. A moment of inattention while operating the hedge trimmer may result in serious personal injury. -
Page 8: Assembly
HEDGE TRIMMER SAFETY WARNINGS (cont.) • Always disconnect the Hedge Trimmer from the mains when leaving the Hedge Trimmer unattended. • Disconnect the Hedge Trimmer from the mains before carrying out maintenance or cleaning work. • Inspect and maintain the Hedge Trimmer regularly. Have the Hedge Trimmer repaired only by an authorized repairer. -
Page 9: Operation
OPERATION Cord retainer When attaching an extension cord to the Hedge Trimmer, hook the end of the extension cord into the cord retainer (8) built into the rear of the Hedge Trimmer's housing (Fig. 2). Using the retainer prevents accidental disconnection of the trimmer and extension cords plug and socket. - Page 10 OPERATION (cont.) Trimming Instructions 1. Extension cord. Always keep the extension cord behind the Trimmer and away from the trimming operation. Never drape it over a hedge being trimmed. If you cut or damage the cord, unplug it at the electrical outlet immediately.
-
Page 11: Maintenance
Always replace both carbon brushes at the same time. Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the tool by an unauthorised person or by mishandling of the tool. -
Page 12: Spare Parts
SPARE PARTS Limited spare parts are available subject to availability. Please contact your local Bunnings Special Orders Desk to order the required spare parts. Most common spare parts listed below Spare Part Part No. Carbon Brush (Pair) SPHTE360-21 Brush Holder (Pair) SPHTE360-30 Blade Assembly SPHTE360-34... -
Page 13: Pack Contents
Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. PACK CONTENTS 1 x Hedge Trimmer HTE-360 1 x Blade cover 1 x Safety guard 4 x Screws ST4x12 (for fitting guard) -
Page 14: Warranty
PURCHASED FROM: ________________________________________________ DATE PURCHASED: ________________________________________________ 2 YEAR REPLACEMENT WARRANTY Your Ozito tool is guaranteed for a period of 24 months from the ORIGINAL date of purchase under the following conditions: Professional, industrial or high frequency use will VOID this warranty.
Need help?
Do you have a question about the HTE-360 and is the answer not in the manual?
Questions and answers