Table of Contents
Advertisement
SUPERSERVER 1028UX-LL1-B8/LL2-B8/LL3-B8 User's Manual
Port 0 ~ Port 5 SATA Device Type
Use this item to specify if the SATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
sSATA Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the PCH-sSATA controller and displays
the following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH-sSATA controller. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The op-
tions are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
sSATA Port 0~ Port 1
This item displays the information detected on the installed on the sSATA port.
specified by the user.
•
Model number of drive and capacity
•
Software Preserve Support
sSATA Port 0~ Port 1
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
7-20
sSATA Port 0 ~ Port 1 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a sSATA disk drive installed on this port
without shutting down the system. The options are Enabled and Disabled.
sSATA Port 0 ~ Port 1 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 1 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to IDE, the following items will
display:
sSATA Port 0~ Port 1
This item indicates that an sSATA port specified by the user is installed (pres-
ent) or not.
Port 0 ~ Port 1 sSATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the sSATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
sSATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
driver for system boot. The options are Disabled, EFI, and Legacy.
sSATA Port 0~ Port 1
This item displays the information detected on the installed sSATA drives on the
particular sSATA port.
7-21
Chapter 7: BIOS
Advertisement
Table of Contents
