Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ganz DR-16F44-AT
Summary of Contents for Ganz DR-16F44-AT
-
Page 2: Table Of Contents
CONTENT OVERVIEW Safety Instruction Caution Key Features What’s included? Front Panel Rear Panel Remote Control At a Glance INSTALLATION HDD Installation/Replacement Basic Layout Connecting to an external devices ２... -
Page 3: Safety Instruction
OVERVIEW Safety Instruction This product was tested with a UPS to satisfy EN 61000-4-11 test conditions (voltage dips and short interruptions test) under the EN 50130-4: 2011 standard. For your safety, we provide a few instructions about installation, manipulation, cleaning, assembly/disassembly of the product as below. -
Page 4: Caution
OVERVIEW CAUTION Replaceable batteries Risk of Explosion if Battery is replaced by an Incorrect type. Dispose of Used Batteries According to the instructions. Warning to service personnel Double pole / neutral fusing. Ethernet Instruction This equipment is indoor use and all the communication wiring are limited to inside of the building or similar word. -
Page 5: What's Included
OVERVIEW What's included? Mouse Remote Control Power Cable & Batteries (AAA x2) DC12V Adaptor Adaptor cable retainer clip Screws fro HDDs Terminal Block (9Px2) Terminal Block (10Px4) Quick Guide User manual CD ５... -
Page 6: Front Panel
OVERVIEW Front Panel Name Description IR Remote Control Receive the signal from the remote control Receiver Used for connecting USB storage or mouse. Status LED Show the status of power, recording or network connection together with the corresponding alarm. HDD 1~5 / Indicates connection status of internal/external storage HDD1 HDD2... -
Page 7: Rear Panel
OVERVIEW Rear Panel 16 Channel Name Description VIDEO IN Video input terminal for cameras. AUDIO IN Port for audio input. AUDIO OUT Port for speaker connection. ALARM IN Alarm input signal port. ALARM OUT Alarm output signal port (TTL Level) RELAY Relay Terminal output port. -
Page 8: Remote Control At A Glance
OVERVIEW Remote Control At a Glance LOGOUT POWER Log out Turn on or off the power. PANIC SEARCH Start the emergency recording. Display the search window. ALARM Show the alarm status with ARCHIVE a popup window. Display the backup window. SETUP Channel Display the system setup menu. -
Page 9: Change The Remote Control Id
OVERVIEW Change the remote control ID The remote control will be active only if the remote control ID matches with that specified on the DVR. If multiple DVRs are installed on one place and you have just a single remote control, use the ID button to set the remote control ID. -
Page 10: Installation
INSTALLATION HDD Installation/Replacement 1. Remove 2 screws on both ends of DVR. 2. Pull the front side of the unit forward to separate it. 3. Hold the middle of the HDD brackets handle with index finger and pull it toward while sustaining the bracket handle with your thumb and middle finger as shown in the illustration. - Page 11 INSTALLATION 4. Once the HDD bracket is separated from the main unit, remove 4 screws on both ends of HDD bracket to separate the HDD. 5. Install a new HDD and fasten 4 screws back to both ends of the bracket to fix. ...
-
Page 12: Basic Layout
INSTALLATION Basic Layout Since the cable quality may affect directly to the video quality depending on the distance between the camera and DVR, it’s recommended to consult an authorized installer when installing the DVR. １２... -
Page 13: Connecting To An External Device
INSTALLATION Connecting to an external device Connecting to the monitor This product supports 1080p 60 Hz HDMI monitors and regular monitors that support DVI and VGA inputs. Connect an HDMI cable to the port on the product’s rear bottom, or connect and HDMI-DVI converter cable to connect a DVI monitor. - Page 14 INSTALLATION Alarm I/O Connection To connect the Alarm input signal Connect the signal line of an alarm input device such as sensor to rear [ALARM IN] port Loosen screws on both the alarm input port and [GND] of the terminal block plug. Insert one end of alarm signal cable through [IN1] to [IN8] terminal hole, and then fasten the screw.
-
Page 15: Audio Device Connection
INSTALLATION Communication Port RS-485 Connection Connect a PTZ Camera of Keyboard Controller. You can connect a text-in device such as POS or ATM. After connecting the control device, be sure to match the connection settings between DVR and the device. Refer to communication settings in “Operation Manaul”. Connect three signals ([D+],[D-],[GND]) between DVR and of the control device by using provided terminal block. -
Page 16: Storage And Mouse Connection
INSTALLATION Storage and Mouse Connection External HDD USB Storage Mouse (For backup only) eSATA Storage If the storage space is insufficient, you can extend your storage capacity by adding an eSATA storage device to the rear eSATA port. Using devices other than recommended eSATA products may causes serious problem. USB Device You connect and use USB storage devices for backup of recorded video, saving snapshot, firmware updating, importing/exporting user configurations. -
Page 17: Network Connection
INSTALLATION Network Connection PC connection in the local network You can connect DVR to a PC in the same network and control or manipulate it on the PC monitor. Connect the [WAN(UPLINK)] port in the rear panel to the router or hub. Do NOT connect any devices to the [LAN (DOWNLINK)] port. - Page 18 INSTALLATION PC connection from a remote network You can connect DVR to a PC from a remote network and control or manipulate it on the PC monitor. Connect the [WAN(UPLINK)] port in the rear panel to the router. Do NOT connect any devices to the [LAN (DOWNLINK)] port. Connect the [WAN(UPLINK)] port of the router directly to the fixed IP LAN cable, or connect it to the ADSL modem.
Need help?
Do you have a question about the DR-16F44-AT and is the answer not in the manual?
Questions and answers