Operation - Denon DRA-F101 Operating Instructions Manual

ENGLISH
7

OPERATION

(1) Playback
3 7
MEMORY TUNING SOURCE
FUNCTION TONE TIMER DISPLAY / SET DOWN UP BAND DIRECT
SYSTEM
ON / STANDBY
PHONES
2
OFF ON
2
SYSTEM
POWER
PROG /
DIRECT
STOP PLAY VOLUME
/SELECT
PRESET
+
5
-
TAPE
SLEEP FUNCTION MODE
3
CD
TUNER
MD
1
Check that all connections are correct.
Turn on the power.
• The indicator first flashes green, then after
about 6 seconds stops flashing, remaining lit,
indicating that the unit is set to the power on
mode.
SYSTEM
ON / STANDBY ON
SYSTEM
POWER
(Main unit) (Remote control unit)
2
Power on/standby mode and function
2
memory
B When the remote control unit is used to
turn the DRA-F101's power on from the
standby mode, the function is set to the
function that was selected when the
power was last set to the standby mode.
(Last memory function)
B If the function has been cleared from the
memory, the function is set to "CD" when
the DRA-F101's power is turned on.
12
Either turn the FUNCTION dial on the main unit
or press the remote control unit's FUNCTION
button to select the function source to be
played.
• The function switches in the order shown
VOLUME
below.
The function switches in the opposite order
when the dial is turned counterclockwise (.).
AM-FM STEREO RECEIVER DRA-F101
5
3
FUNCTION
(Main unit) (Remote control unit)
CD TUNER
MD TAPE
Start playback of the selected function source.
4
• For instructions on operation, refer to the
component's operating instructions.
Adjust the volume.
VOLUME
5
(Main unit) (Remote control unit)
Adjust the BALANCE, BASS, and TREBLE
controls and set the LOUDNESS position to the
6
desired position.
For instructions on adjusting, see "(3) Setting
the various modes" on page 12, 13.
To use the source direct function:
Press the SOURCE DIRECT button to display
"SD ON" .
7
(2) Recording
1
Follow step 1 to 4 under "(1) Playback".
Start recording on the cassette deck or MD
recorder.
For instructions, refer to the component's
operating instructions.
• Operating the VOLUME, BALANCE, BASS,
TREBLE and the LOUDNESS controls will not
2
affect the sound being recorded.
• When the function source is set to "MD",
recording is performed from the MD recorder
onto the cassette deck. When the function
FUNCTION source is set to "TAPE", recording is
performed from the cassette deck onto the
MD recorder.
DVD/AUX
PHONO
VOLUME
/SELECT
SOURCE
DIRECT
(Main unit)
(3) Setting the various modes
2 1
VOLUME
MEMORY TUNING SOURCE
FUNCTION TONE TIMER DISPLAY / SET DOWN UP BAND DIRECT
SYSTEM
ON / STANDBY
PHONES
AM-FM STEREO RECEIVER DRA-F101
STOP PLAY VOLUME
/SELECT
PRESET
+
2
-
TAPE
SLEEP FUNCTION MODE
1
[1] Adjusting the bass and treble
Press the TONE or MODE button to display the
mode to be adjusted ("BASS" or "TREBLE").
TONE
MODE
(Main unit) (Remote control unit)
1
• The mode switches as follows each time the
button is pressed:
BASS TREBLE LOUDNESS
Playback BALANCE
function source
This cannot be selected when the source
direct mode is set to "ON".
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
/SELECT
(increase)
FUNCTION
(decrease) (increase)
(decrease)
(Main unit) (Remote control unit)
2
• To increase the bass or treble:
Turn the dial clockwise (,) or press the
button.
To decrease the bass or treble:
Turn the dial counterclockwise (.) or press
the button.
H
• The bass and treble can be adjusted within
the range of –8 to 0 to +8 in steps of 2. The
response is flat at 0.
D