Related Manuals for HP SLATE 8 PLUS
Summary of Contents for HP SLATE 8 PLUS
- Page 1 HP Slate 8 Plus Tablet Maintenance and Service Guide IMPORTANT! This document is intended for HP authorized service providers only.
- Page 2 By installing, copying, downloading, or otherwise using any software product preinstalled on this tablet, you agree to be bound by the terms of the HP End User License Agreement (EULA). If you do not accept these license terms, your sole remedy...
- Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
- Page 4 Safety warning notice...
-
Page 5: Table Of Contents
Table of contents 1 Product description ......................1 2 External component identification ..................3 3 Illustrated parts catalog ....................4 Locating the tablet part number, serial number, and IMEI number ........... 4 Tablet major components ......................5 Miscellaneous parts ........................7 Sequential part number listing .................... - Page 6 System board ........................27 Rear-facing webcam ....................... 29 Vibrator module ........................30 6 Specifications ........................32 7 Power cord set requirements ..................33 Requirements for all countries ....................33 Requirements for specific countries and regions ................. 33 8 Recycling ........................35 Index ..........................
-
Page 7: Product Description
Product description Category Description Product Name HP Slate 8 Plus Tablet Chipset/processor Balong® V9R1 Cortex-A9 quad core 1.60-GHz processor Graphics Integrated with solder-on-circuit (SoC) Panel 8.0-in, 1280×800, diagonal capacitive, 10-point MultiTouch, in-plane switching (IPS), high- definition (HD), wide-viewing angle display panel... - Page 8 Category Description Operating system Preinstalled: Android 4.4.2 Serviceability End user replaceable parts: AC adapter and USB cable Chapter 1 Product description...
-
Page 9: External Component Identification
External component identification Item Component Item Component Microphone Volume control buttons Audio-out (headphone)/Audio-in Microphone (microphone) jack Front-facing webcam Micro USB port Power button Speakers... -
Page 10: Illustrated Parts Catalog
Illustrated parts catalog Locating the tablet part number, serial number, and IMEI number The tablet part number (1), serial number (2), and International Mobile Station Equipment Identity number (IMEI) (3) are located on the tablet back cover. This information may be needed when travelling internationally or when contacting support. -
Page 11: Tablet Major Components
Tablet major components Item Component Spare part number Display panel assembly (8.0-in, 1280×800, diagonal capacitive, 10-point 775651-001 MultiTouch, IPS, HD, wide-viewing angle, includes front bezel) Speaker Kit, includes: 775653-001 (2a) Top speaker Tablet major components... - Page 12 Item Component Spare part number (2b) Bottom speaker and cable Delivery antenna board (includes double-sided adhesive) 775647-001 1.0-MP, fixed-focus front-facing webcam (includes cable and double- 775655-001 sided adhesive) 5.0-MP, auto-focus rear-facing webcam (includes cable and double- 775656-001 sided adhesive) System board equipped with a Balong V9R1 Cortex-A9 quad core 1.6-GHz 775654-001 processor, 1.0-GB of system memory, 16-GB eMMC system storage Volume button board (includes cable and grounding tape)
-
Page 13: Miscellaneous Parts
For use in the United Kingdom and Singapore 773125-003 HP Slate 8 Plus Tablet: HP Slate 8 Plus Tablet equipped with an 8.0-in, 1280×800, diagonal capacitive, 10-point 775644-001 MultiTouch, IPS, HD, wide-viewing angle display panel, a Balong V9R1 Cortex-A9 quad core 1.6-GHz processor, 1.0-GB of system memory, 16-GB eMMC system storage, and a 1-cell, 4800-... -
Page 14: Sequential Part Number Listing
775644-001 HP Slate 8 Plus Tablet equipped with an 8.0-in, 1280×800, diagonal capacitive, 10-point MultiTouch, IPS, HD, wide-viewing angle display panel, a Balong V9R1 Cortex-A9 quad core 1.6- GHz processor, 1.0-GB of system memory, 16-GB eMMC system storage, and a 1-cell, 4800-... - Page 15 Spare part number Description 775656-001 5.0-MP, auto-focus rear-facing webcam (includes cable and double-sided adhesive) 780960-001 USB dongle Sequential part number listing...
-
Page 16: Removal And Replacement Preliminary Requirements
Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: Flat-bladed screw driver ● Magnetic screw driver ● Phillips P00 screw driver ● Torx5 screw driver ● Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. -
Page 17: Drive Handling
Drive handling CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. - Page 18 CAUTION: To prevent damage to the computer when you are removing or installing internal components, observe these precautions: Keep components in their electrostatic-safe containers until you are ready to install them. Before touching an electronic component, discharge static electricity by using the guidelines described in this section.
-
Page 19: Packaging And Transporting Guidelines
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ●... -
Page 20: Equipment Guidelines
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps ● with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. -
Page 21: Removal And Replacement Procedures
Accessing these components can damage the tablet or void the warranty. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for the tablet/keyboard, go to http://partsurfer.hp.com, select the country or region, and then follow the on-screen instructions. -
Page 22: Display Panel Assembly
Remove the top and bottom covers (2). Reverse this procedure to install the top and bottom covers. Display panel assembly Description Spare part number Display panel assembly (8.0-in, 1280×800, diagonal capacitive, 10-point MultiTouch, IPS, HD, 775651-001 wide-viewing angle, includes front bezel) Before removing the back cover, follow these steps: Turn off the tablet. - Page 23 CAUTION: Before positioning the tablet with display panel facing down, make sure the work surface is clear of tools, screws, and any other foreign objects. Failure to follow this caution can result in damage to the display panel. Position the tablet with the display panel facing down and the micro SD Card Reader slot toward you.
-
Page 24: Battery
WARNING! To reduce potential safety issues, use only the battery provided with the tablet, a replacement battery provided by HP, or a compatible battery purchased from HP. CAUTION: Removing a battery that is the sole power source for the tablet can cause loss of information. -
Page 25: Speakers
Remove the battery: Remove the Phillips PM1.4×2.5 screw (1) that secures the battery cable bracket to the system board. Remove the battery cable bracket (2). Disconnect the battery cable (3) from the system board. Insert a case utility tool (4) or similar thin tool between the battery and the back cover, and then detach the battery from the back cover. - Page 26 Remove the speakers: Remove the Phillips PM1.4×2.5 screw (1) that secures the battery cable bracket to the system board. Remove the battery cable bracket (2). Disconnect the battery cable (3) from the system board. Remove the two Phillips PM1.4×2.5 screws (1) that secure the top speaker to the back cover. Disconnect the bottom speaker cable (2) from the system board.
-
Page 27: Delivery Antenna Board
Delivery antenna board Description Spare part number Delivery antenna board (includes double-sided adhesive) 775647-001 Before removing the delivery antenna board, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 28: Front-Facing Webcam
Detach the delivery antenna board (3) from the back cover. (The delivery antenna board is attached to the back cover with double-sided adhesive.) Remove the delivery antenna board and RF cable. NOTE: The RF cable is included in the back cover spare part kit, spare part number 775642-001. - Page 29 Disconnect the battery cable (3) from the system board. Disconnect the front-facing webcam cable (1) from the system board. Detach the front-facing webcam (2) from the back cover. (The front-facing webcam is attached to the back cover with double-sided adhesive.) Remove the front-facing webcam and cable.
-
Page 30: Volume Button Board
Volume button board Description Spare part number Volume button board (includes cable and grounding tape) 775646-001 Before removing the volume button board, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 31: Connector Board
Release the volume button board (3) from the clips built into the back cover. Remove the volume button board and cable. Reverse this procedure to install the volume button board. Connector board Description Spare part number Connector board (includes cable, micro SD Card Reader slot, and micro SIM slot) 775648-001 Before removing the connector board, follow these steps: Turn off the tablet. - Page 32 Disconnect the battery cable (3) from the system board. Disconnect the connector board cable (1) from the system board. Remove the two Phillips PM1.4×2.5 screws (2) that secure the connector board to the back cover. Remove the connector board (3). Reverse this procedure to install the connector board.
-
Page 33: System Board
System board Description Spare part number System board equipped with a Balong V9R1 Cortex-A9 quad core 1.6-GHz processor, 1.0-GB of 775654-001 system memory, 16-GB eMMC system storage Before removing the system board, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. - Page 34 Detach the rear-facing webcam from the back cover. (The rear-facing webcam is attached to the back cover with double-sided adhesive.) Disconnect the RF antenna cable (1) from the antenna terminal on the system board. Disconnect the front-facing webcam cable (2) from the system board. Release the ZIF connector (3) to which the volume button board cable is attached, and then disconnect the volume button board cable from the system board.
-
Page 35: Rear-Facing Webcam
Lift the rear edge of the system board (3) until it rests at an angle, and then remove the system board by sliding it up and back at an angle. Reverse this procedure to install the system board. Rear-facing webcam Description Spare part number 5.0-MP, auto-focus, rear-facing webcam (includes cable and double-sided adhesive) -
Page 36: Vibrator Module
Remove the rear-facing webcam: Disconnect the rear-facing webcam cable from the system board. Remove the rear-facing webcam and cable. Reverse this procedure to install the rear-facing webcam. Vibrator module Description Spare part number Vibrator module (includes cable and double-sided adhesive) 775649-001 Before removing the vibrator module, follow these steps: Turn off the tablet. - Page 37 Detach the vibrator module (2) from the back cover. (The vibrator module is attached to the back cover with double-sided adhesive.) Remove the vibrator module and cable. Reverse this procedure to install the vibrator module. Vibrator module...
-
Page 38: Specifications
The tablet operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50/60 Hz, 0.3-1.0 A. NOTE: The tablet can operate on DC power using an industry-standard micro-B USB cable. The HP adapter included with your tablet is recommended for charging the tablet. Temperature Operating 5°C to 35°C... -
Page 39: Power Cord Set Requirements
Power cord set requirements The wide-range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased. - Page 40 Country/region Accredited agency Applicable note number Germany Italy Japan METI The Netherlands KEMA Norway NEMKO The People's Republic of China South Korea Sweden CEMKO Switzerland Taiwan BSMI The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
-
Page 41: Recycling
Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle. -
Page 42: Index
Index display panel assembly headphone 3 AC adapter, spare part numbers removal 16 microphone 3 7, 8 spare part number 5, 8, 16 antenna board display panel, product memory, product description 1 removal 21 description 1 microphone spare part numbers 6, 8, 21 drives locations 3 audio, product description 1... - Page 43 sensors 1 serviceability 2 vibrator module storage 1 removal 30 video 1 spare part number 6, 8, 30 wireless 1 video, product description 1 product name 1 volume button board removal 24 spare part number 6, 8, 24 rear-facing webcam volume control button 3 removal 29 spare part number 6, 9, 29...