Operation - Toro 07390 Workman HDX-Auto Operator's Manual

•
Remove equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel such
equipment with a portable container, rather than from a
fuel dispenser nozzle.
•
Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock open device.
•
If fuel is spilled on clothing, change clothing immediately.
•
Never overfill fuel tank. Replace fuel cap and tighten
securely.

Operation

•
The operator and passenger should remain seated and
use the seat belts whenever the vehicle is in motion. The
operator should keep both hands on the steering wheel,
whenever possible, and the passenger should use the hand
holds provided. Keep arms and legs within the vehicle
body at all times. Never carry passengers in the box or
on attachments. Remember your passenger may not be
expecting you to brake or turn and may not be ready.
•
Never overload your vehicle. The name plate (located
under the middle of the dash) shows the load limits for
the vehicle. Never overfill attachments or exceed the
vehicle maximum gross vehicle weight (GVW).
•
When starting the engine:
– Sit on operator's seat and ensure that the parking
brake is engaged.
– Disengage PTO (if so equipped) and return the hand
throttle lever to the Off position (if so equipped).
– Make sure the hydraulic lift lever is in the center
position.
– Press in the brake pedal.
– Keep your foot off of the accelerator pedal.
– Turn the ignition key to the Start position.
•
Using the machine demands attention. Failure to operate
machine safely may result in an accident, tip over of the
machine, and serious injury or death. Drive carefully.
To prevent tipping or loss of control, take the following
precautions:
– Use extreme caution, reduce speed, and maintain
a safe distance around sand traps, ditches, creeks,
ramps, any unfamiliar areas, or other hazards.
– Watch for holes or other hidden hazards.
– Use caution when operating the vehicle on a steep
slope. Normally, travel straight up and down slopes.
Reduce speed when making sharp turns or when
turning on hillsides. Avoid turning on hillsides
whenever possible.
– Use extra caution when operating the machine on
wet surfaces, at higher speeds, or with a full load.
Stopping time will increase with a full load.
– When loading the bed, distribute the load evenly.
Use extra caution if the load exceeds the dimensions
of the vehicle/bed. Operate the machine with extra
caution when handling off-center loads that cannot
be centered. Keep loads balanced and secure to
prevent them from shifting.
– Avoid sudden stops and starts. Do not go from
reverse to forward or forward to reverse without first
coming to a complete stop.
– Do not attempt sharp turns or abrupt maneuvers or
other unsafe driving actions that may cause a loss of
control of the machine.
– Do not pass another machine traveling in the same
direction at intersections, blind spots, or at other
dangerous locations.
– When dumping, do not let anyone stand behind
machine and do not dump the load on anyone's feet.
Release the tailgate latches from the side of box, not
from behind.
– Keep all bystanders away. Before backing up, look to
the rear and ensure that no one is behind the vehicle.
Back up slowly.
– Watch out for traffic when near or crossing roads.
Always yield the right of way to pedestrians and
other vehicles. Always signal your turns or stop early
enough so other persons know what you plan to do.
Obey all traffic rules and regulations.
– Never operate the machine in or near an area where
there is dust or fumes in the air which are explosive.
The electrical and exhaust systems of the machine can
produce sparks capable of igniting explosive materials.
– Always watch out for and avoid low overhangs such
as tree limbs, door jambs, over head walkways, etc.
Make sure there is enough room over head to easily
clear the machine and your head.
– If you are ever unsure about the safe operation of the
machine, stop your work and ask your supervisor.
•
Before getting off the seat:
– Stop movement of the machine.
– Lower bed.
– Shut engine off and wait for all movement to stop.
– Set parking brake.
– Remove key from ignition.
•
Do not touch engine, transmission, radiator, muffler or
muffler manifold while engine is running or soon after
it has stopped because these areas may be hot enough
to cause burns.
•
If the machine ever vibrates abnormally, stop the machine
immediately, turn engine off, wait for all motion to
stop and inspect for damage. Repair all damage before
resuming operation.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
5