Operating Tips - Toro 07390 Workman HDX-Auto Operator's Manual

causes the oil flow to go over a relief valve, which can
damage the hydraulic system.
•
On position
This position is similar to Lower (quick coupler B
position). It also directs hydraulic oil to quick coupler
B except that the lever is held in this position by the
hydraulic-lift lock in the control panel. This allows oil
to flow continuously to equipment that uses a hydraulic
motor. Use this position only when you are operating the
machine with an attachment with a hydraulic motor.
Important: If you are using the machine with a
hydraulic cylinder or no attachment, the On position
causes the oil flow to go over a relief valve, which can
damage the hydraulic system. Use this position only
momentarily or with a motor attached.
Important: Check the hydraulic oil level after
installing an attachment. Check the operation of
the attachment by cycling it several times to purge
air from system, then check the hydraulic oil level.
The attachment cylinder will slightly affect transaxle
oil level. Operating the machine with low oil level
can damage the pump, remote hydraulics, power
steering, and the machine transaxle.
CAUTION
Hydraulic fluid escaping under pressure can
have sufficient force to penetrate skin and do
serious damage. Care must be used when
connecting or disconnecting hydraulic quick
couplers. Stop the engine, apply the parking
brake, lower the attachment, and place the
remote hydraulic valve in the float detent
position to relieve hydraulic pressure before
connecting or disconnecting quick couplers.
Connecting the Quick Couplers
Important: Clean dirt from quick couplers before
connecting. Dirty couplers can introduce contamination
into the hydraulic system.
1. Pull back the locking ring on the coupler.
2. Insert the hose nipple into the coupler until it snaps
into position.
Note: When attaching remote equipment to the quick
couplers, determine which side requires pressure, then attach
that hose to quick coupler B which will have pressure when
the control lever is pushed forward or locked in the On
position.
Disconnecting the Quick Couplers
Note: With both the machine and attachment turned off,
move the lift lever back and forth to remove the system
pressure and to make disconnecting the quick couplers easier.
1. Pull back the locking ring on the coupler.
2. Pull the hose firmly from the coupler.
Important: Clean and install the dust plug and
dust covers to the quick coupler ends when not
in use.

Operating Tips

Operating Characteristics
The machine is designed with safety in mind. It uses familiar
automotive style controls, including the steering wheel, brake
pedal, and accelerator pedal,. It is important to remember,
however, that this machine is not a passenger car. It is a work
vehicle and is designed for off road use only.
WARNING
The machine is designed primarily as an off-road
vehicle and is not intended for extensive use on
public roads.
Occasional use on public roadways should only be
undertaken with respect to local traffic regulations
and using any additional accessories that may be
required by local law (including but not limited to
lights, turn signals, slow moving vehicle (SMV)
sign, etc).
The machine has special tires, low gear ratios, a locking
differential, and other features that give it extra traction.
These features add to the versatility of the vehicle but, they
can also get you into dangerous situations. You must keep in
mind that the vehicle is not a recreation vehicle, it is not an all
terrain vehicle, and, it is definitely not meant for stunt driving
or horsing around. It is a work vehicle, not a play vehicle.
Children should not be allowed to operate the machine.
Anyone who operates the machine must be properly trained.
The driver and passenger should always use the seat belts.
If you are not experienced at driving the machine, practice
driving it in a safe area away from other people. Be sure
you are familiar with all the machine's controls, particularly
those used for braking, steering, and transmission shifting.
Learn how your machine handles on different surfaces.
Your operating skills will improve with experience, but as in
operating any vehicle, take it easy as you begin. Be sure you
know how to stop quickly in an emergency. If you need help,
ask your supervisor for assistance.
Many factors contribute to accidents. You have control over
several of the most important. Your actions, such as driving
too fast for conditions, braking too fast, turning too sharp,
and combinations of these, are frequent cause of accidents.
One of the major causes of accidents is fatigue. Be sure to
take occasional breaks. It is very important that you stay
alert at all times.
Never operate the machine, or any equipment, if you
are under the influence of alcohol or other drugs. Even
31