Table of Contents
Advertisement
Quick Links
FMM 2
Spinnit
R
USER'S MANUAL
Before operating this equipment, please read these
instructions completely and keep these operating
instructions for future reference.
-
Manual Paper Drill
485 Hague Street, Rochester, NY 14606 U.S.A.
Tel: 585-436-1934
www.lasscowizer.com
Serial Number:
Date of Purchase:
Dealer:
Address:
Telephone Number:
Fax: 585-464-8665
info@lasscowizer.com
Advertisement
Table of Contents
Related Manuals for Lassco Spinnit FMM-2
Summary of Contents for Lassco Spinnit FMM-2
- Page 1 FMM 2 Spinnit Manual Paper Drill USER’S MANUAL Serial Number: Date of Purchase: Dealer: Address: Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. Telephone Number: 485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com...
-
Page 2: Table Of Contents
1 - Introduction 1.1 - Your New FMM-2 Paper Drill Your New FMM-2 Paper Drill....Page 01 Thank you for your purchase of the Spinnit FMM-2 Shipping Damage Inspection....Page 01 Paper Drill. We ask that you take a moment to fill in the serial... -
Page 3: Safety
2 - Safety 2.1 - Safety Instructions All operators must read and understand the Users KEEP CHILDREN AWAY. All visitors should be kept a safe Manual including all safety instructions before using this distance from the work area. equipment. Failure to fully understand the safety instructions can result in personal injury. -
Page 4: Warning Labels
2 - Safety 2.2 - Warning Labels English French WARNING: DO NOT EXPOSE TO RAIN AVERTISSEMENT: NE PAS EXPOSER OR USE IN DAMP LOCATIONS. À LA PLUIE ET NE PAS UTILISER DANS LES EMPLACEMENTS HUMIDES Page 03... -
Page 5: Grounding Instructions
2.3 - Grounding Instructions Diagram 2-10 METAL SCREW COVER OF GROUNDED OUTLET BOX GROUNDING In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to re- duce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conduc- tor and a grounding plug. -
Page 6: Setting Up Your Machine
7/32” T Style (1) FM4-4001: 25” Drill Strip (1) (this item comes installed) 3.2 - Accessories Warning USE RECOMMENDED ACCESSORIES. Only use accessories approved by a Lassco-Wizer. The use of improper acces- sories may cause risk of injury to persons. Page 05... -
Page 7: Uncrating And Removing From The Pallet
3 - Setting Up Your Machine 3.3 - Uncrating and Removing From the Pallet 3.3.1 Remove the wooden framing around the outside box. 3.3.2 Remove the box up and over the machine. 3.3.3 Remove the two (2) 5/16” bolts which are securing the machine to the pallet: access through the rear of the machine using a 5/16”... -
Page 8: Attaching The Paper Side Stops
3 - Setting Up Your Machine 3.5 - Attaching the Paper Side Stops 3.5.1 Attach the Paper Side Stops (FM4-4006) using two (2) Side Stop Diagram 3-30 Screws (FM4-4007) each. Position the Paper Side Stop as de- sired and tighten down with light pressure. Side Stop Screws Paper Side Stop Table... -
Page 9: Operation
4 - Operation 4.1 - Protective Guard 4.1.1 Your FMM-2 comes with a protective guard installed. DO NOT Diagram 4-10 operate this machine without the guard in place. 4.1.2 Please note that when you are performing certain operations such as removing and installing drill bits, you will need to move the guard out of the way. -
Page 10: Leveling The Drill Bits
4 - Operation 4.3 - Leveling the Drill Bits 4.3.1 We recommend using a piece of card stock on the Diagram 4-40 Table when leveling the drill bits to avoid drilling into 1/8” Hex Wrench the drill strip. This will lengthen the life of your drill bits and keep them sharper. -
Page 11: Adjusting The Table Height
4 - Operation 4.4 - Adjusting the Table Height 4.4.1 After you level the drill bits you may need to adjust your table Diagram 4-80 height. Test drill through a stack of scrap approximately the same Table height as that you will be drilling. If the drill bits drill into the Drill Strip or if the drill bits fail to penetrate through the bottom sheet of scrap you will need to adjust the table height. -
Page 12: Adjusting The Distance Between
4 - Operation 4.6 - Adjusting the Distance Between Heads 4.6.1 To adjust the spindles to a desired spacing, loosen the Hand Diagram 4-100 Wheel Lock Knob. Turn the Hand Wheel to move the spindle Shroud farther away from the center or to move the spindle closer to the center. -
Page 13: Multi-Hole Set-Up
4 - Operation 4.8 - Multi-hole Set-Up 4.8.1 If a hole pattern includes more than three (3) holes, you will need to adjust the Stop Collars to the desired spacing. The Stop Collars are adjusted as descibed in section 4.7. To set the distance between the stop collars, follow steps 4.8.2 through 4.8.5. -
Page 14: Drilling Procedures
4 - Operation 4.10 - Drilling Procedures 4.10.1 After all your adjustments are made as desired, position the Table Diagram 4-160 in its original position. Set the product to be drilled on the table and make sure it is secure using the Paper Side Stops. To drill, step down on the Foot Treadle raising the Table up to meet the drill bits. -
Page 15: Maintenance
5 - Maintenance 5.1 - Safety ALWAYS DISCONNECT THE POWER BEFORE PERFORMING MAINTENANCE ON THIS MACHINE. MAINTENANCE SHOULD ONLY BE PERFORMED BY A QUALIFIED TECHNICIAN. KEEP HANDS CLEAR WHILE PERFORMING MAINTENANCE ON THIS MACHINE. MOVING PARTS CAN CRUSH AND CUT. 5.2 - Annual Lubrication 5.2.1 Lubricating your FMM-2 should be done at least once every 12... - Page 16 5 - Maintenance 5.2 - Annual Lubrication 5.2.5 Press down on the Foot Treadle to Raise the Table. Manually Diagram 5-40 holding the Table in place, slowly let up on the Foot Treadle so that the Push Rods in the rear of the machine fall out of the Pin Housings.
-
Page 17: Inspecting The Flex Drive
5 - Maintenance 5.2 - Annual Lubrication 5.2.10 Apply a light grease on the two (2) Traverse Rods either by hand Diagram 5-70 or with a small brush to the points indicated in diagram 5-70. Crank both heads in and out to distribute the lubrication and to Grease Grease check the head movement. -
Page 18: Trouble Shooting Guide
6 - Trouble Shooting Guide 6.1 - Determining the Cause and Correction to Certain Problems Problem Cause Correction Drill bit not concentric. Foreign material in chuck or in Inspect and clean. drill plug. Drill bit is bent. Replace drill bit. Drill bit not seated in chuck Re-insert drill bit correctly. - Page 19 6 - Trouble Shooting Guide 6.1 - Determining the Cause and Correction to Certain Problems Problem Cause Correction Machine vibrates, wobbles, The machine is not level on the Use the leveling feet to make the floor. machine level on the floor. See resonates, etc.
- Page 20 6 - Trouble Shooting Guide 6.1 - Determining the Cause and Correction to Certain Problems Problem Cause Correction The Drive Pulley is loose. Adjust the Drive Pulley to the Uncommon metallic sounds proper height and tighten or from under the shroud. replace the Set Screw.
-
Page 21: Parts Diagrams
7 - Parts Diagrams 7.1 - Side View Page 20... -
Page 22: Head Assembly
7 - Parts Diagrams 7.2 - Head Assembly Page 21... -
Page 23: Spindle And Chuck Assembly
7 - Parts Diagrams 7.3 - Spindle and Chuck Assembly Page 22... -
Page 24: Rear View
7 - Parts Diagrams 7.4 - Rear View Page 23... -
Page 25: Parts List
7 - Parts Diagrams 7.5 - Parts List FMM9-9534: Motor FM4-4000: Table FMM9-9513: Drive Belt FM4-401A: Pedestal Stop Assembly Grease Fitting EBM-47: Stop Collar FMM8-8504: Hand Wheel FM4-4014: Stop Collar Rod FMM8-8508: Hand Wheel Lock Knob FM7-7002: Backgauge Clamping Bracket FMM9-9517: Shroud Locking Knob FM3-3007: Pin Housing FMM8-8503: Traverse Lead Screw...