Maintenance And Troubleshooting - ICON Health & Fitness WESLO CADENCE S5 User Manual

21. Do not change the incline of the treadmill by
placing objects under the treadmill.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never drop or insert any object into any
opening.
DANGER:
24. Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been placed on the
treadmill. If the decal is missing, or if it is not legible,
call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply
the decal in the location shown. Note: The decal is not
shown at actual size.
Hungarian
Russian
232971
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
Polish Portugese
4

MAINTENANCE AND TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 10). If an exten-
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
d. Check the on/off switch located on the treadmill
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the cir-
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the "on" position (see d. above).
e. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
English:
sion cord is needed, use only a 3-conductor, 1 mm
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
near the power cord. The switch must be in the "on"
position.
cuit breaker has tripped, wait for five minutes and then press the switch back in.
five minutes, and then plug it back in.
POWER CORD. Remove the five indicated Screws
(20) and the two Foot Rail Screws (25). Then, care-
fully remove the Hood (65).
Locate the Reed Switch (97) and the Magnet (113) on
the left side of the Pulley (104). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.). If necessary,
loosen the Screw (21), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Hood, and
run the treadmill for a few minutes to check for a cor-
rect speed reading.
17
2 (14-gauge) cord that is no longer than 1.5 m
c
Tripped Reset
d
On
Position
a
20
65
20
20
25
3 mm
21 104
113
97
Top View