Table of Contents
Advertisement
Quick Links
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than those specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
1
Digital Day/Night Vandal Resistant Dome Camera
Advertisement
Table of Contents
Related Manuals for Genie CCTV VRCD-5351
Summary of Contents for Genie CCTV VRCD-5351
- Page 1 The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
-
Page 2: Features
Warning Features The camera requires periodic inspection. Horizontal Resolution of 540 TV High Sensitivity Contact an authorised technician to carry out the inspection. Lines The built-in high sensitivity SONY COLOUR Clear image quality has been achieved by Stop using your camera when you find it malfunctioning. CCD enables clear image even at 0.3Lux employing a SONY CCD with 410,000 (0.002Lux in Sense-up) -
Page 3: Table Of Contents
Contents Features Camera Operation Menu Warnings and Precautions Settings • LENS (selection) Components • SHUTTER (condition and speed control) Names and Functions of Parts • WHITE BALANCE control Lens • BLC (Back Light Compensation) • AGC (Auto Gain Control) VBS-EXTRA •... - Page 4 Precautions Do not install the camera in Do not install or use the camera in an Do not drop the camera or protect Never keep the camera pointed extreme temperature conditions. environment where the humidity is high. it from physical shocks. directly at strong light.
-
Page 5: Components
Components Names and Functions of Parts 1. COLOUR DOME CAMERA 2. SCREWS 3. WRENCH 4. WIRE FOR VBS-EXTRA 5. INSTRUCTION GUIDE Digital Day/Night Vandal Resistant Dome Camera Digital Day/Night Vandal Resistant Dome Camera... -
Page 6: Names And Functions Of Parts
Names and Functions of Parts Names and Functions of Parts LENS : Vari-Focal DC Auto Iris Lens VBS-EXTRA FOR CONNECTING TO SERVICE MONITOR Please use the supplied wire when connecting to external monitor VBS-EXTRA 3 AXIS BRACKET Please loosen screws and fix in to tilted and panned position. (unit : mm) SMPS PCB FOR DUAL POWER - IF APPLICABLE OSD PCB... -
Page 7: Installation
Installation 1. Dome Base Mounting - Open the dome cover by loosening the 3 screws, using the special RUBBER wrench provided. GASKET - Mount the base of the camera to a sturdy surface using the 4 screws (1.5 inch) and the 4 pre-made holes on the base of the dome. 2. -
Page 8: Camera Operation
Camera Operation Menu Settings Settings can be made using the 5 buttons located inside the camera. SETUP menu LENS (selection) •MANUAL •DC SHUTTER •ESC •MANUAL •FLK (condition and speed control) WHITE BALANCE control •ATW •AWC •MANUAL BACKLIGHT •OFF •LOW •MIDDLE (Backlight Compensation) •HIGH AGC (Auto Gain Control) -
Page 9: Lens (Selection)
Camera Operation MANUAL : Manual Lens selection SETUP DC : Auto Iris Lens selection Select any function you Modes can be changed LENS wish to operate by using the LEFT and SHUTTER using the UP and RIGHT buttons. WHITE BAL. DOWN buttons. -
Page 10: Shutter (Condition And Speed Control)
Camera Operation SHUTTER (condition and speed control) WHITE BALANCE control Auto or manual control can be selected. The screen colours can be adjusted using the WHITE BALANCE function. 1. When the SETUP menu is on the screen, position the cursor to point to 1. -
Page 11: Blc (Back Light Compensation)
Camera Operation BLC (Back Light Compensation) AGC (Auto Gain Control) When there is a strong backlight behind the object, clear images of the 1. Position the cursor to point to 'AGC' on the SETUP menu by using the background as well as the object can still be obtained by using the UP and DOWN buttons. -
Page 12: Dnr (Digital Noise Reduction)
Camera Operation DNR (Digital Noise Reduction) The level of background noise in low light decreases automatically as the 1. Position the arrow to point to 'SENS UP' on the SETUP menu by using the level of gain changes. UP and DOWN buttons. 2. -
Page 13: Special
Camera Operation SPECIAL 1. Position the cursor to point to 'SPECIAL' on the SETUP menu by using the 3) Press the SET button. UP and DOWN buttons. 2. Select the mode required by pressing the UP or DOWN button. 4) Up to 15 characters can be used for the camera ID. Move the cursor to the letter required by using the UP and DOWN button. - Page 14 Camera Operation 5) When the camera ID is complete, select a position for the name to be Note displayed. • When the AGC is turned off, COLOUR does not operate. • When an infrared light is used, there may be a problem with focusing. Move the cursor onto 'POS' and then press the SET button.
-
Page 15: Exit
Camera Operation MOTION DETECTION: • Select the area you do not wish to appear from the 4 areas in the AREA SEL mode. This product has a feature that allows you to observe movements of objects • Select ON mode for the chosen area. in 4 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected;... -
Page 16: Troubleshooting
Troubleshooting If there are problems with the camera operation, check the tables below. If Problems Troubleshooting the problem persists, please contact the agent who supplied the product. The MOTION • Check if 'MOTION DETECTION' mode is DETECTION function is Problems Troubleshooting turned on. -
Page 17: Specifications
ON / OFF (4 Programmable Zone) Operating Temperature / Humidity - 10°C ~ +50°C / 30~90% RH 1,100g Weight ※ ※ OPTION - Dual Voltage : VRCD-5351/DV - Heater : VRCD-5351H - Colour : VRCD-5351/W Digital Day/Night Vandal Resistant Dome Camera... -
Page 18: Digital Day/Night Vandal Resistant Dome Camera
Model : VRCD-5351 Digital Day/Night Vandal Resistant Dome Camera Instruction Guide GENIE CCTV LTD. CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT Tel : +44 (0) 1707 330541 Fax : +44 (0) 1707 330543 www.geniecctv.com...