Table of Contents
Advertisement
Operating Instructions
OPERATING INSTRUCTIONS
Connecting the LP gas cylinder to the grill
The LP Gas Cylinder must be a 20 pound cylinder and have a Type 1 Cylinder Valve Outlet
●
Connector.
Handle the Cylinder with care - do not drop it.
●
When you are not using the grill, the LP Gas Cylinder should be dis-
●
connected.
Connect the regulator and hand tighten firmly.
●
Do a leak test each time you connect a LP Gas Cylinder and before
●
lighting the grill.
Never use a match or lit flame to test for leaks.
●
To test, prepare a weak solution of detergent and water. Spray or
●
swab the solution onto the connection of the regulator to the LP Gas
Cylinder valve, and on all the joints in the hose connections up to the burner valves (which
MUST be closed in the "OFF" position).
Open the LP Gas Cylinder valve, and watch for any bubbles to appear at all the connection
●
points. No bubbles indicate - All Clear!
If there are any bubbles, there is a leak which must be fixed.
●
Never obstruct the flow of combustion and ventilation air.
●
Lighting the grill
Always open the Lid before lighting the grill.
1. Read instructions before lighting.
●
All burner knobs should be in the "OFF" position.
2. Open Lid during lighting.
●
3. Make sure all control knobs are OFF.
Open the LP Gas Cylinder valve,1 – 1 1/2 turns.
●
4. Turn on gas supply.
Select one burner to light. Push and turn control knob to "LIGHT"
●
Position.
5. (2-Burner Models) Push in and turn the left control knob counterclockwise to "LIGHT" position. This
Press the electronic igniter button and hold for 5 seconds to light burner.
burner must be lit first before other burner can be lit.
●
You can then adjust the knob to your desired setting.
●
(3-Burner Models) Push in and turn the middle control knob counterclockwise to "LIGHT" position.
If the burner did not light, turn the knob back to the "OFF" position, wait 5 minutes for any gas
●
This burner must be lit first before other burners can be lit.
to clear away, and then repeat the lighting procedure.
(4-Burner Models) Push in and turn either of the middle control knobs counterclockwise to "LIGHT"
Follow same steps to light the other burners.
●
position. The two middle burners must be lit first before other burners can be lit.
After using the grill, - turn all burner knobs to the "LIGHT" position and then push fully in and
●
6. Press the ignitor button rapidly several times until the burner is lit.
turn to the "OFF" position.
If the ignitor does not light the burner, you can light it with a match or a piece of burning paper. Hold the match or paper
At once turn the valve on the LP Gas Cylinder OFF.
●
with the Match Holder (attached to the side of the grill), put it through opening in Cooking Grid and next to the Flame Tent
IF the igniter does NOT light the burner, you can light it
covering the burner. Then follow the lighting procedure above.
●
with a match or a piece of burning paper - hold the
7. For cooking with more burners, push in and turn the control knob
match or paper with the Match Holder ( attached at the side
counterclockwise until the burner is lit.
of the grill) , put it through the openings in the Cooking Grid
WARNING: If ignition does not occur in 5 seconds, immediately turn the
and next to the Flame Tent covering the burner. Then fol-
burner controls OFF, wait 5 minutes and repeat the lighting process.
low the lighting procedure above.
WARNING: Turn the gas supply off when not in use.
Observe the proper burner flame - it should be a blue/
●
yellow color about 1/2" long.
After using the grill, turn all burner knobs to the "LIGHT" position
and then push fully in and turn to the "OFF" position. Turn OFF
the valve on the LP Gas Cylinder.
Good Flame
Good Flame
Good
Flame
19
Bad Flame
Bad Flame
YELLOW
YELLOW
Yellow
BLUE
BLUE
Blue
Burner
Burner
Burner
Observe the proper burner
flame. It should be a blue/yellow
color about 1/2" long.
Bad
Flame
Advertisement
Table of Contents
