Advertisement
Firmware Upgrades
The firmware of the scaler can be upgraded via the internal web pages or the Extron Firmware Loader program (available on the Extron website,
www.extron.com). The internal web pages cannot be accessed through the USB port.
Basic SIS Command Table
IN1608 scalers can be configured with specific SIS commands via an RS-232, USB, or Ethernet connection. Use the Extron DataViewer utility
or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and
variables, see the IN1608 User Guide at www.extron.com.
Command
Select audio and video input
Select video input only
Select audio input only
Execute Auto-Image
Execute Auto-Image and fill
Execute Auto-Image and follow
Mute video to black
Mute video and sync
Unmute video and sync
NOTE:
By default, adjusting variable volume with the following commands only affects variable analog output (configurable through group
masters).
Set variable volume level
Raise variable volume
Lower variable volume
View variable volume level
NOTE:
By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
View master audio mute status
Enable executive mode 1
Enable executive mode 2
Disable executive modes
Set scaler IP address
Set scaler DHCP mode
Set subnet mask
Set gateway IP address
Reboot networking
NOTE:
IP settings will not take effect until the
NOTES:
X!
= Input selection (1-8)
X(
= Enable or disable (0 = off or disabled; 1 = on or enabled)
X4)
= IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4!
= Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@
= Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
X4$
= Group volume level (-1000 to 0, where -1000 = -100 dB or 0% volume and 0 = 0 dB or 100% volume)
X4*
= Increment value (dB value multiplied by ten, in 0.1 dB increments, to raise or lower a group fader [for example, 100 = 10 dB])
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
4
ASCII Command
Response
(Host to Device)
(Device to Host)
X!
X! •
!
In
X!
X! •
&
In
X!
X! •
$
In
A
Img0
1*A
Img1
2*A
Img2
1B
Vmt1
2B
Vmt2
0B
Vmt0
}
E
X4$
D8*
GRPM
GrpmD08*
E
X4*
}
D8*
+GRPM
GrpmD08*
E
X4*
}
D8*
-GRPM
GrpmD08*
E
}
X4$]
D8GRPM
E
X(
}
D7*
GRPM
GrpmD07*
E
}
X(]
D7GRPM
1X
Exe1
2X
Exe2
0X
Exe0
EX4)
}
CI
Ipi
EX(
}
DH
Idh
EX4!
}
CS
Ips
EX4@
CG
}
Ipg
E
}
2BOOT
Boot2
E
}
2BOOT
command is executed.
Extron USA - West: +1.714.491.1500
Extron USA - East: +1.919.850.1000
Additional Description
]
All
Selects audio and video input
]
RGB
Selects the video only input
]
Aud
Selects the audio only input
Executes an Auto-Image on the current input.
]
]
Executes an Auto-Image and fills the output.
]
Executes an Auto-Image and maintains the aspect ratio
of the current input.
]
Mutes the video and displays a black output.
Mutes the video and sync output.
]
]
Unmutes the video.
]
X4$
Set the variable volume to a value of
]
X4$
Increase the level of the variable volume by
]
X4$
Decrease the level of the variable volume by
View the current variable volume level.
X(]
Enable or disable master audio mute.
View the current master audio mute status.
]
Locks the entire front panel.
]
Locks the front panel except for input selection and
volume control.
]
Allows all front panel adjustments and selections.
Specifies a new scaler IP address.
• X4)]
X(]
Enables or disables DHCP (0 = default).
• X4!]
Specifies a new subnet mask.
Specifies a new gateway IP address.
• X4@]
]
Restarts the network connection after IP or DHCP
changes.
FAX: +1.714.491.1517
FAX: +1.919.850.1001
X!
.
X!
.
X!
.
X4$
.
X4*
dB.
X4*
dB.
www.extron.com
68-1916-50 Rev. A
06 13
Advertisement
