Related Manuals for Horizon Fitness OMEGA 2
Summary of Contents for Horizon Fitness OMEGA 2
- Page 1 OMEGA 2 OMEGA 3 TREADMILL OWNER’S MANUAL Read the TREADMILL gUIDE before using this OWNER’S MANUAL.
- Page 2 ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
-
Page 3: Tools Included
PRE ASSEMBLY TooLS INCLUDED: F 6 mm L-Wrench CONSOLE F 6 mm T-Wrench UNPACKING CELLPHONE AND MP3 STORAGE F 5 mm L-Wrench with Philip Screw Driver AUDIO IN/OUT JACK WATER BOTTLE HOLDER Place the treadmill carton on a level flat surface. It is recommended that you place a Omega 3 protective covering on your floor. -
Page 4: Assembly Step
ASSEMBLY STEP 1 ASSEMBLY STEP 2 Cut the yellow banding straps and lift the running Open HARDWARE BAG 2. HARDWARE foR STEP 1 : HARDWARE foR STEP 2 : deck upward to remove all contents from underneath Put down LEFT & RIGHT HANDLEBAR and fix it into the running deck. Omega 3 Omega 3 BOLT (A) - Page 5 CONSOLE using 1 SCREW (B). YOU ARE FINISHED! Qty: 1 Fix your CONSOLE angle by tightening the ADJUSTMENT KNOB from STEP B. Omega 2 55 DEGREES Max. User Weight: 125 kg / 275 lbs CONSOLE NOTE: Tighten all bolts and screws and make...
-
Page 6: Treadmill Operation
TREADMILL OPERATION This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the TREADMILL gUIDE has instructions for the following: • LoCATIoN of THE TREADMILL • USING THE SAfETY KEY • foLDING THE TREADMILL • MoVING THE TREADMILL • LEVELING THE TREADMILL • T ENSIoNING THE RUNNING BELT •... - Page 7 A) LARGE LED WINDoWS: Time, Distance, Calories, Heart Rate, Speed, Incline and Workout Profiles. TIME DISTANCE ZEIT ENTFERNUNG B) LCD WINDoW: Calories, Heart Rate, Incline, Speed, %Complete, and Scan. C) fEEDBACK LEDS: Indicate what workout feedback is currently being displayed in the LCD window. Omega 2 Omega 2 INCLINE SPEED Shown STEIGUNG GESCHWINDIGKEIT D) PRoGRAM LEDS: Indicate what program is currently selected.
- Page 8 oMEGA 3 CoNSoLE oPERATIoN Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) TARGET LED INDICAToRS: Indicate what target (if any) is set for the current program. TARGETS TIME DISTANCE CALORIES ZIELE ZEIT ENTFERNUNG KALORIEN...
-
Page 9: Display Windows
OMEgA 2 DISPLAYS OMEgA 3 DISPLAYS TIME DISTANCE TARGETS TIME DISTANCE CALORIES ZEIT ENTFERNUNG ZIELE ZEIT ENTFERNUNG KALORIEN TIME DISTANCE ZEIT ENTFERNUNG Omega 2 Omega 3 Shown Shown SPEED INCLINE STEIGUNG GESCHWINDIGKEIT INCLINE SPEED CALORIES STEIGUNG GESCHWINDIGKEIT KALORIEN HEART RATE... -
Page 10: Getting Started
GETTING STARTED B) SELECT A PRoGRAM CHANGING YoUR TARGET MID-WoRKoUT TARGET PRofILES (oMEGA 3 oNLY) (oMEGA 3 oNLY) 1) Check to make sure no objects are placed on the 1) Select a program using or +/– and press ENTER to TARGET 1 – TIME: Allows user to set a target based belt that will hinder the movement of the treadmill. confirm. - Page 11 CoNSoLE oPERATIoN WoRKoUT PRofILES MYKEYS 1) MANUAL – ALL MoDELS: Allows ‘on the fly’ manual speed and incline changes. You can program the MyKeys to your desired speed or incline values. 2) INTERVALS – ALL MoDELS: Improves your strength, speed and endurance by increasing and decreasing the speed The SPEED MYKEYS defaults are: The INCLINE MYKEYS defaults are: throughout your workout to involve your heart and other muscles.
-
Page 12: Finishing Your Workout
To RESET THE CoNSoLE 4) HILL RUN Hold STOP key for 3 seconds. HILL RUN - oMEGA 2 oNLY: Simulates running up and down hills to improve stamina. Elevation and speed changes, time defaults as 30 minutes. fINISHING YoUR WoRKoUT When your workout is complete, the monitor display will flash “FINISHED” and beep. Your workout information will stay displayed on Segment Warm Up Segments 1–8... - Page 13 DESCRIPTION DESCRIPTION CONSOLE SET;SA;TM676-2KM; SIDE RAIL FIxING WASHER;TM08-141F; CONNECT TUBE;TM676-2KM; SCREW;BH;M8x1.25Px30L;HS;G12.9;BZN; MOTOR SET;SA;-;TM676; ORNAMENT;RUNNING DECK;PVC;BL;TM37B Omega 2 Omega 2 Shown Shown COTOR COVER SET;U;TM676 ELASTOMER;FIxED;LASTOMERIC;R;TM290-1US FRAME; SILK SCREEN;BLACK;TM676; RVN;ALS7-8125-3.8(0.5-3.8);yZN; CONSOLE MAST SET;L;PAINTING;TM676 SCREW;BH;Φ4x12L;TC;PH;BAN;POT CONSOLE MAST SET;R;PAINTING;TM676 AIR STICK;DAMPING;35KG;359-581L; ELEVATION RACK SET;PAINTING;TM676 BUFFER PAD;ELASTOMERIC;60°;G;TM367-2KM...
- Page 14 DESCRIPTION DESCRIPTION DESCRIPTION MOTOR;AC ELEVATION;220V;80MM;225;10PIN;J INDUCTANCE;6MH 200,300;ADD LABEL;TM80 SIDE RAIL;L;TM403 MCB;DIGITAL 1.75HP;220V;MLH0910HEPE;S490 WIRE;CTRL BOARD PWR;WHITE;250LOCK300L COVER;L;ABS;75140;TM415-2KM MOTOR FIxNG PLATE;PAINTING;LIGHT S SCREW;FH;M3x0.5Px10L;PH;ZN; COVER;R;75140;TM415-2KM Omega 2 Omega 2 Shown Shown MOTOR ELASTOMER PAD;RUBBER;TM16 SCREW;BH;M5x0.8Px25L;CT;PH;NKL; SIDE RAIL;R;TM403 SCREW;SH;5/16”18UNCx16L;HS;BP NUT;Hx;M5x0.8P;SS41;NKL; SCREW;BH;Φ4x15L;TC;PH;BAN;POT WASHER;FLT;Φ8.2xΦ16.0x0.8T; WASHER;TOOTH;Φ5.3xΦ10.0x0.6T;BAN; SCREW;BH;Φ4x12L;TC;PH;BZN;POT WASHER;SPL;Φ8.2xΦ15.4x2.0T;...
- Page 15 oMEGA 3 ExPLoDED VIEW DESCRIPTION SCREW;BH;M8x1.25Px30L;HS;G12.9;BZN; CONSOLE SET;SA;TM677-2KM; SCREW;HH;M10x1.5Px45L-15L; CONNECT TUBE SET;SA;TM677-2KM; ELASTOMER ORANGE MOTOR SET;SA;TM677; ELASTOMER BLUE Omega 3 Omega 3 Shown Shown MOTOR COVER SET;UP;TM677-2KM FIxING BUMPERC FRAME;SILK SCREEN;BLACK;TM677; DIRECTION LABEL;CARB-2; CONSOLE MAST SET;L;PAINTING;TM676 FIxING BUMPERC;BLACK;TM616-1US CONSOLE MAST SET;R;PAINTING;TM676 NUT;NLK;M8x1.25P;BZN; ELEVATION RACK SET;PAINTING;TM676 SCREW;M8x1.25Px9L-D10x11.2L;HE;45#;BOx BASE FRAME SET;PAINTING;TM676 WASHER;FLT;Φ10.5xΦ20.0x1.0T;TFN;...
- Page 16 DESCRIPTION DESCRIPTION DESCRIPTION SCREW;SH;5/16”18UNCx16L;HS;BP SCREW;BH;M5x0.8Px25L;CT;PH;NKL; COVER;RIGHT/REAR;ABS;75140;TM621 WASHER;FLT;Φ8.2xΦ16.0x0.8T; NUT;Hx;M5x0.8P;SS41;NKL; DOCUMENTATION;SIDERAIL;R;PAD PRINT;T WASHER;SPL;Φ8.2xΦ15.4x2.0T; WASHER;TOOTH;Φ5.3xΦ10.0x0.6T;BAN; COVER;SIDE RAIL;LEFT;BLACKE;TM626; Omega 3 Omega 3 Shown Shown SCREW;SH;M8x1.25Px55L;HS;BZN; WAVE FILTER(6A);06SS-2DC-C COVER;SIDE RAIL;RIGHT;BLACKE;TM626; SCREW;HH;3/8-16UNCx45L-15L;HE;BZN;P-T WAVE TUBE; CR-11SP;Φ14xΦ10.7;200M/COIL SCREW;TRH;Φ4x12L;TC;PH;;BAN;POT SCREW;HEx;M10x55L-14L;BED SCREW;TRH;Φ4x10L;TC;PH;NKL;POT SCREW;TRHW;Φ4x20L;TC;PH;POT WASHER;ARC;Φ8.2xΦ18.0x1.5T;BAN; WIRE;PCB CONNECTION;1800L(CKM254301-8P+S SCREW;BH;Φ4x25L;SM;PH;BZN;POT NUT;NLK;3/8’-16UNC;;BAN; PWR CORD(INDIA);1.5MM;LONG2M SCREW;TRH;Φ4x16L;SM;PH;POT NUT;NLK;M10x1.5P;BAN;...
- Page 17 Horizon Fitness - Produkte sind recyclebar. Führen Sie das gerät am Ende der Nutzungsdauer einer sachgerechten Entsorgung zu (örtliche Sammelstelle). GB: Waste Disposal Horizon Fitness products are recyclable. At the end if its useful life please dispose of this article correctly and safely (local refuse sites). f: Remarque relative à la gestion des dèchets Horizon Fitness sont recyclables.
- Page 19 TREADMILL OWNER’S MANUAL Omega 2 & 3 Owner’s Manual 061912 Rev. 1 © 2012 Horizon Fitness...