Specifications - Makita 2414EN Instruction Manual

ENGLISH (Original instructions)
1-1. Base
1-2. Bolt holes
2-1. Lock-off button
2-2. Switch trigger
3-1. Screw
3-2. Spark guard
4-1. Socket wrench
4-2. Guide plate
4-3. Move
4-4. Hex bolts
6-1. Socket wrench
6-2. Guide plate
6-3. Hex bolts
7-1. Clamping screw
7-2. Safety guide

SPECIFICATIONS

Wheel diameter
No load speed (min
Dimensions (L x W x H)
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in ferrous materials with
appropriate abrasive cut-off wheel. Follow all laws and
regulations regarding dust and work area health and
safety in your country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause
voltage fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.21 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow
tripping characteristics.
Explanation of general view
10-1. Shaft lock
10-2. Socket wrench
11-1. O-ring
11-2. Inner flange
11-3. Ring
11-4. Spindle
11-5. Cut-off wheel
11-6. Outer flange
11-7. Hex bolt
12-1. Vise plate
12-2. Vise nut
12-3. Vise handle
13-1. Spacer block
14-1. Guide plate
14-2. Straight piece of wood (Spacer)
Model
Hole diameter
-1
)
With under cover
With European type safety
guard and under cover
Safety class
ENE007-3
Noise
The typical
according to EN61029:
Sound pressure level (L
Sound power level (L
ENF002-2
Uncertainty (K) : 3 dB(A)
Vibration
The vibration
ENF100-1
determined according to EN61029:
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
4
14-3. Over 45 mm long
14-4. Over 65 mm long
14-5. Over 190 mm long
15-1. Diameter of workpiece
15-2. Guide plate
15-3. Spacer block
15-4. Width of spacer block
15-5. Vise
16-1. Blocks
17-1. Under cover
17-2. Wing bolt
19-1. Limit mark
20-1. Screwdriver
20-2. Brush holder cap
2414EN
355 mm
25.4 mm
3,800
500 mm x 280 mm x 620 mm
17.6 kg
/II
A-weighted noise
) : 102 dB(A)
pA
) : 112 dB(A)
WA
Wear ear protection
total value (tri-axial
) : 3.5 m/s
h
2
ENG905-1
level determined
ENG900-1
vector sum)
2
ENG901-1