Warning Messages; Diagnostics Messages; Alert Messages - Dell PowerEdge 6600 Installation And Troubleshooting Manual

1-2-2 DMA initialization failure
1-2-3 DMA page register write/read failure
1-3-1 Main-memory refresh verification failure
1-3-2 No memory installed
1-3-3 Chip or data line failure in the first 64 KB of main memory
1-3-4 Odd/even logic failure in the first 64 KB of main memory
1-4-1 Address line failure in the first 64 KB of main memory
1-4-2 Parity failure in the first 64 KB of main memory
1-4-3 Fail-safe timer test failure
1-4-4 Software NMI port test failure
2-1-1 Bit failure in the first 64 KB of main memory
through
2-4-4
3-1-1 Slave DMA-register failure
3-1-2 Master DMA-register failure
3-1-3 Master interrupt-mask register failure
3-1-4 Slave interrupt-mask register failure
3-2-2 Interrupt vector loading failure
3-2-4 Keyboard-controller test failure
3-3-1 CMOS failure
3-3-2 System configuration check failure
3-3-3 Keyboard controller not detected
3-3-4 Video memory test failure
3-4-1 Screen initialization failure
3-4-2 Screen-retrace test failure
3-4-3 Video ROM search failure
4-2-1 No timer tick
4-2-2 Shutdown test failure
4-2-3 Gate A20 failure
4-2-4 Unexpected interrupt in protected mode
4-3-1 Improperly installed or faulty memory modules
4-3-2 No memory modules installed in bank 1
4-3-3 Faulty I/O board
4-3-4 Time-of-day clock stopped
4-4-1 Super I/O chip failure; faulty I/O riser card
4-4-2 BIOS-shadowing failure
4-4-3 Microprocessor speed control sequence failure
4-4-4 Cache test failure; faulty microprocessor
NOTE: For the full name of an abbreviation or acronym used in this table, see

Warning Messages

A warning message alerts you to a possible problem and asks you to take corrective action before the system continues a task. For example, before you
format a diskette, a message may warn you that you may lose all data on the diskette. Warning messages usually interrupt the procedure and require you to
respond by typing y (yes) or n (no).
NOTE: Warning messages are generated by either the application program or the operating system. For more information, see
Solutions" and the documentation that accompanied the operating system or application program.

Diagnostics Messages

When you run a test group or subtest in system diagnostics, an error message may result. Diagnostic error messages are not covered in this section. Record
the message on a copy of the Diagnostics Checklist (see

Alert Messages

The optional systems management software generates alert messages for your system. For example, the software generates messages that appear in the
SNMP trap log file. Alert messages consist of information, status, warning, and failure messages for drive, temperature, fan, and power conditions. For more
See "Troubleshooting System
"Troubleshooting Your System."
See "Troubleshooting the I/O
Board" in "Troubleshooting Your System."
See "Troubleshooting the I/O Riser
See "Troubleshooting the I/O Riser
"Troubleshooting Your System."
See "Troubleshooting Expansion
See "Troubleshooting System
Install memory modules of the same type and size in bank 1 (see
Modules" in "Installing System Options").
See "Troubleshooting the I/O
See "Troubleshooting the System
in "Troubleshooting Your System."
See "Troubleshooting the I/O Riser
See "Troubleshooting the I/O
"Troubleshooting Your System."
See "Troubleshooting the Microprocessor
"Abbreviations and
"Getting Help"), and then follow the instructions in that section for obtaining technical assistance.
Memory" and "Troubleshooting the I/O
Board" and "Troubleshooting the Microprocessor
Card" in "Troubleshooting Your System."
Card" and "Troubleshooting the I/O
Cards" in "Troubleshooting Your System."
Memory" in "Troubleshooting Your System."
Board" in "Troubleshooting Your System."
Battery" and "Troubleshooting the I/O Riser
Card" in "Troubleshooting Your System."
Board" and "Troubleshooting System
Board" in "Troubleshooting Your System."
Acronyms."
Board" in
Board" in
"Installing Memory
Card"
Memory" in
"Finding Software