Dell 6100 Hardware Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. 6100
  6. Hardware manual
Dell 6100 Hardware Manual

Dell 6100 Hardware Manual

Microprocessor replacement
Hide thumbs Also See for 6100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
Š
Š
®

Advertisement

Table of Contents
loading

Related Manuals for Dell 6100

Summary of Contents for Dell 6100

  • Page 1 Š Š ®...

  • Page 2: Warnings, Cautions, And Notes

    Intel Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

  • Page 3: Precautionary Measures

    Dell PowerEdge Microprocessor Replacement his document provides the procedures for replacing the Intel microprocessor(s) in a Dell PowerEdge 6100/200 system. Unless otherwise noted, each procedure assumes the following: • You have performed the steps in “Precautionary Measures” that follows. •...

  • Page 4: Bios Upgrade

    2. Turn on the system. 3. After the system completes the boot routine, follow the instructions on 4. After the message BIOS has been successfully installed Dell PowerEdge 6100/200 System Microprocessor Replacement IOS Upgrade the monitor. appears on the monitor, remove the diskette from drive A and follow...

  • Page 5: C Omputer Cover

    3. Slide the cover toward the back of the computer an inch or so. Then grasp the top of the cover at both ends, and lift it straight away from the chassis. keylock (locked position) screw (6) Dell PowerEdge 6100/200 System Microprocessor Replacement...

  • Page 6: S Upport Panel

    Figure 3. Support Panel Removal 1. Remove the left computer cover. 2. Remove the support panel. Dell PowerEdge 6100/200 System Microprocessor Replacement upport Panel slot (2) screw (2) Remove the two screws from the support panel and pull the back edge tabs...
  • Page 7 NOTES: Both microprocessor module connectors must be populated. The secondary connector must have either another microprocessor module or a terminator module. Be careful not to touch components or the gold edge connectors on the module. Dell PowerEdge 6100/200 System Microprocessor Replacement...
  • Page 8 Dell part number 95545. All 200 MHz/1 MB microprocessors must be used in conjunction with Dell BIOS Revision A05 or greater and Dell customer diagnos- tics software 3.79D00 or greater. The BIOS and diagnostics software are available through the Dell bulletin board service (BBS) and the Dell Web site at www.dell.com.
  • Page 9 (passive). The processor(s) cache is 1 MB. The processor(s) cache is 512 KB. SEL1 (Pins 3-4) SEL2 (Pins 5-6) No jumper No jumper No jumper No jumper No jumper Jumper No jumper Jumper Dell PowerEdge 6100/200 System Microprocessor Replacement...

  • Page 10: M Icroprocessor And Heat Sink

    To remove the microprocessor/heat sink assembly, follow these steps: 1. Remove the left computer cover. 2. Remove the support panel and the appropriate microprocessor module. 3. Remove the microprocessor securing clip from the microprocessor/heat Dell PowerEdge 6100/200 System Microprocessor Replacement icroprocessor and Heat Sink microprocessor socket sink assembly (see Figure 7).
  • Page 11 CAUTION: Be careful not to bend any of the pins when removing the microprocessor chip from its socket. Bending the pins can perma- nently damage the microprocessor chip. microprocessor securing clip hooks over tabs on socket (front and back) microprocessor socket microprocessor Dell PowerEdge 6100/200 System Microprocessor Replacement...
  • Page 12 See your system User’s Guide for more information about these settings. Dell PowerEdge 6100/200 System Microprocessor Replacement release lever Figure 8. Removing a Microprocessor...
  • Page 14 ® www.dell.com Printed in the U.S.A. P/N 81655...

This manual is also suitable for:

Poweredge 6100/200

Table of Contents