Pattern Sequencer; Realtime Erase; Saving A Pattern As A "Performance" (Save As Perform); Turning The Display Backlight On/Off - Roland juno-ds61 Parameter Manual

Pattern Sequencer

5 In the PATTERN SEQUENCER screen, you can long-press the [LOOP] button to open
the LOOP window, where you can make loop-related settings. Press the [EXIT]
button to close the LOOP window.
Parameter Explanation
Specifies whether playback will loop (ON) or not loop (OFF).
* You can also switch this by pressing the [LOOP] button.
Loop Switch
OFF, ON
Specifies whether to loop-record (ON) or not loop-record (OFF).
* You can also switch this by pressing the [LOOP] button while holding
Loop Rec
down the [SHIFT] button.
OFF, ON
5 Use the [UPPER] slider to adjust the level of track 1, and the [LOWER] slider to adjust
the level of track 2.
5 Use the [PHRASE PAD] slider to increase or decrease the level that's specified for
tracks 3–8 while maintaining the balance between these tracks.
5 Press the [MIXER] button to open the MIXER screen. Here you can set the pan and
level of each track.
You can use pads [1]–[8] to select a track to edit.
Use the [UPPER]/[LOWER]/[PHRASE PAD] sliders to adjust the level.
MEMO
Tracks 1–7 are assigned to parts 1–7, and track 8 is assigned to part 10.

Realtime Erase

Erasing only specified notes during recording or playback
(REALTIME NOTE ERASE)
1 .
During recording or playback, hold down the [RHYTHM PATTERN] button
and press the [ERASE] button.
The REALTIME NOTE ERASE window appears.
2 .
Press a key on the keyboard to specify the note that you want to erase.
3 .
Press the [ERASE] button.
While you continue holding down the key, only the note you specify is erased from
the selected track.
Erasing only movements of knobs or the bender/modulation lever
during recording or playback
1 .
During recording or playback, hold down the [MUTE] button and press the
[ERASE] button.
Only while you continue holding down these buttons, movements of the knobs and
the bender/modulation lever are erased from the selected track.

Saving a Pattern As a "Performance" (SAVE AS PERFORM)

Settings related to the sound of the pattern (preset/user) used in the pattern
sequencer can be saved as a performance.
For example, if you want to export a pattern to SMF, use your DAW to edit it into a
complete song, and then use the JUNO-DS to play this song data, the performance
saved by the "SAVE AS PERFORM" function can be recalled to play the data using the
original sound.
1 .
In the PATTERN SEQUENCER screen, select a pattern.
2 .
Press the [MENU] button.
The MENU screen appears.
3 .
Move the cursor to "PATTERN UTILITY," and press the [ENTER] button.
4 .
Move the cursor to "SAVE AS PERFORM," and press the [ENTER] button.
The SAVE AS PERFORM screen appears.
5 .
Use the value dial to select the write destination performance, and press
the [ENTER] button.
A confirmation message appears.
If you decide to cancel, press the [EXIT] button.
6 .
Move the cursor to "OK," and press the [ENTER] button.
Writing is complete when the screen indicates "Completed!"
NOTE
Never turn off the power while the screen indicates "Writing.... "

Turning the Display Backlight On/Off

To reduce battery consumption, you can turn off the display backlight when it's not
required.
1 .
Hold down the [SHIFT] button and press the [EXIT] button.
The display backlight will turn off.
Turning the display backlight on
1 .
Hold down the [SHIFT] button and press the [ENTER] button.
The display backlight will turn on.

Demo Songs

1 Wonder
2 There There There
Additional Explanation
Copyright © 2015 Roland Corporation
3