Table of Contents
Advertisement
Quick Links
CEX cover qxd:Varipoint cover qxd
17/10/11
Zip Heaters (UK) Ltd
14 Bertie Ward Way
Dereham
Norfolk
NR19 1TE
Telephone 0845 6024533
Facsimile 01362 692448
www.zipheaters.co.uk
16:41
Page 1
The terms 'Zip' and 'InLine'
are registered trademarks.
9120 - 2546
Installation, Maintenance and User Instructions
Zip InLine
Electronically Controlled Instantaneous
Water Heaters
Models CEX-O & CEX-U
Issued August 2011
Please read these instructions carefully before commencing installation of the InLine water heater.
Please leave these instructions with the end user after installation.
Advertisement
Table of Contents
Related Manuals for Zip CEX-O
Summary of Contents for Zip CEX-O
- Page 1 17/10/11 16:41 Page 1 Installation, Maintenance and User Instructions Zip InLine Electronically Controlled Instantaneous Water Heaters Models CEX-O & CEX-U Issued August 2011 Zip Heaters (UK) Ltd 14 Bertie Ward Way Dereham Norfolk NR19 1TE The terms ‘Zip’ and ‘InLine’...
-
Page 2: Table Of Contents
Furthermore, this warranty does not displace any statutory warranty, but, to the Fault finding extent to which Zip is entitled to do so, the liability of Zip under any statutory warranty will be limited at Zip's option to the replacement of the appliance or... -
Page 3: Description
The maximum inlet temperature of 70°C is suitable for use with preheated water e.g. from solar heating systems. Approvals Zip InLine CEX-O and CEX-U are VDE approved to the LVD and EMC directives and are CE endorsed. Zip InLine CEX-O and CEX-U have been examined, tested and found when correctly fitted to comply with the requirements of the United Kingdom Water Regulations / Byelaws (Scotland). -
Page 4: Warnings
• In case of malfunction isolate the power supply immediately. In case of leaks also isolate the water supply. Repairs must only be carried out by Zip Heaters (UK) Ltd or an authorized Zip service engineer. -
Page 5: Technical Data
• Minimum flow rate 2.0 litres/minute. • A minimum water pressure of 2 bar is recommended for optimum performance. • Maximum flow rate will be achieved at a water pressure of 6 bar. CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... -
Page 6: Dimensions
CEX pages qxd:Varipoint qxd 30/8/11 14:27 Page 4 Dimensions CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... -
Page 7: Spare Parts
IN82812 CEX-U IN82816 CEX-O Control Panel IN82811 IN82512 Main PCB Temperature Sensor Set IN82246 Non-return Valve IN82810 Heating Element c/w STDB IN82819 Flow Sensor IN86250 Terminal Block IN82806 Grommet CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... -
Page 8: Installation
Requirements • These instructions must be read and fully understood before commencing the installation. If in doubt, or in need of further guidance please ring Zip on 0845 602 4533. • Zip InLine water heaters must be installed by a competent person familiar with electric instantaneous water heaters. -
Page 9: Installing The Appliance
7. Ensure that all air is eliminated from the water heater by opening and closing the hot water tap until all air has been eliminated from the water heater and no more air emerges. Fig 3 CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... -
Page 10: Electrical Connection
Ensure all connections are fully tightened and secure. 5. Re-fit the appliance cover taking care not to trap the cable from the display panel and secure the cover with the fixing screw (see Fig 5). CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... -
Page 11: Commissioning
8. Explain operation of the appliance to the end user and leave the operating instructions for their reference. 9. Complete the product registration card and return it to Zip Heaters or register the product on line at www.zipheaters.co.uk CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... - Page 12 1. Disconnect the power supply to the unit. 2. Move the jumper on the main PCB from pin 1 to pin 2. 3. Reconnect the power supply to the unit. CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011...
-
Page 13: Service Menu
Installed software version Radio channel: Radio channel of heater and remote control Received strength: Signal quality of remote control (10% - 100%) Signal: Quality of radio contact with diagnostic display CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... - Page 14 In order to modify system parameters it is necessary to remove the jumper from the main PCB as described under “Deactivation of the Lock level”. CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011...
-
Page 15: Operation
“P1” or “P2” to the new temperature value which becomes available each time the corresponding program key is pressed. Store temperature Set required Press >3 temperature seconds CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011... - Page 16 “10” to “00” in one second Press + hold! intervals. The appliance is reset when the counter reaches “00”. Releasing the function keys earlier will cancel the process. Reset complete CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011...
- Page 17 70ºC. If the inlet temperature exceeds the set point, the “SUN” symbol on the display indicates that the heating power is switched off. CEX-O & CEX-U Installation, Maintenance and User Instructions - August 2011...
-
Page 18: Cleaning And Maintenance
Repairs should only be carried out by competent persons familiar with electric instantaneous water heaters. All service work should be performed by an authorized Zip service engineer – for details of the full range of services available call Zip Service on 0845 602 4533.