Operation - Craftsman 315.SS630 Operator's Manual

:
WaRninG
Do not allow familiarity with products
to make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
:
WaRninG
Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure
to do so could result in fluids entering your eyes
resulting in possible serious injury.
:
WaRninG
Do not use any attachments or
accessories not recommended by the manufacturer
of this product. The use of attachments or
accessories not recommended can result in serious
personal injury.
appLiCaTiOnS
You may use this product for the purposes listed below:
 Interior and exterior painting and staining of decks,
outdoor furniture, fences, and walls
This product will accept Craftsman
battery packs and Craftsman
battery packs.
For complete charging instructions, refer to the Operator's
Manual for the battery packs and chargers listed in the
Specific Safety Instructions.
BaTTERY pROTECTiOn FEaTURES
Craftsman 19.2 V lithium-ion battery packs are designed
®
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO inSTaLL / REMOVE BaTTERY paCK
See Figure 2, page i.
WaRninG
: Always remove battery pack from
your tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
To install:
 Place the battery pack in the tool. Align the raised rib
on the battery pack with groove in the battery port.
 Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in
the tool before beginning operation.

OpERaTiOn

19.2 V lithium-ion
®
19.2 V nickel-cadmium
®
To remove:
 Depress the latches on both sides of the battery pack
to release the battery pack and remove it from the tool.
:
WaRninG
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
:
WaRninG
must be well-ventilated and away from sparks or
flames.
FiLLinG SpRaYER WiTh painT/STain
See Figure 3 - 4, page i.
Remove and discard any skin that has formed on top of
the paint or stain, then thoroughly mix the material in its
original container before beginning.
nOTE: Older containers of stain and paint may need to be
strained before use.
 Remove the battery pack from the sprayer.
 Remove the quick-lock container by twisting counter-
clockwise so that the arrow on the container lines up
with the "unlock" symbol on the lid.
 Fill the container with paint or stain as desired. Do not
fill above the max fill mark on the container.
 Reinstall the container on the sprayer and twist
clockwise so that the arrow on the container lines up
with the "lock" symbol on the lid.
SELECTinG ThE pROpER SpRaY Tip
See Figure 5, page ii.
Use the round tip for latex paints, oil-based paints,
and stains. This tip sprays in a round pattern.
Use the 12 in. fan tip for latex paints. This tip
sprays in a wide pattern that can be adjusted from
horizontal to vertical.
To switch tips:
 Remove the battery pack from the sprayer.
 Remove the installed tip by turning it counter-clockwise.
 Install the desired tip and rotate clockwise to tighten
securely.
nOTE: The tip should be tightened securely by hand. A
too loose or overtightened tip may cause the sprayer to
leak or be damaged.
To change direction of fan tip:
 Slightly loosen the fan tip by rotating counter-clockwise
1/4 turn.
 Rotate the adjusting arm 1/4 turn in the direction
needed to switch the direction of the tip spray.
8 - English
Battery tools are always in operating
Risk of fire or explosion. Spray area