Battery Pack; Operation - Craftsman 315.SS630 Operator's Manual

WARNING:DonotallowfamiUiadty withproducts
to make youcareUess. Remember thata careUess
fraction of a second issufficient t o inflictserious
injury.
WARNING:AUways weareyeprotection w ithside
shbUds m arked to compUy withANSiZ87.1.FaiUure
to dosocouUd r esuUt influidsentering youreyes
resuUting inpossibUe serious injury.
WARNING:Donotuseanyattachments o r
accessories notrecommended bythemanufacturer
ofthisproduct. T heuseof attachments or
accessories notrecommended canresuUt inserious
personaU injury.
APPLICATmONS
You may use this product for the purposes Uistedbebw:
interior and exterior painting and staining of decks,
outdoor furniture, fences, and walls
This product will accept Craftsman _>19.2 V lithium-ion
battery packs and Craftsman _>19.2 V nickePcadmium
battery packs.
For complete charging instructions, refer to the Operator's
Manual for the battery packs and chargers listed in the
Specific Safety instructions.
8ATTI=RY PROT_=CTmON FI=ATURI=S
Craftsman _ 19.2 V lithium-ion battery packs are designed
with features that protect the lithiumqon cells and
maximize battery life.
if the tool stops during use, release the trigger to reset
and resume operation. _fthe tool still does not work, the
battery needs to be recharged.
TO mNSTALL / REMOVE BATTERY PACK
See Figure 2, page L
_ WARNING: Always remove battery pack from
your tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
To install:
Place the battery pack in the tool. Align the raised rib
on the battery pack with groove in the battery port.
Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in
the tool before beginning operation.
To remove:
Depress the latches on both sides of the battery pack
to release the battery pack and remove it from the tool.
_ WARNING: Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
_1_ WARNING: Risk of fire or explosion. Spray area
must be welPventilated and away from sparks or
flames.
FiLLiNG SPRAYER WiTH PAiNT/STAIN
See Figure 3 =4, page L
Remove and discard any skin that has formed on top of
the paint or stain, then thoroughly mix the material in its
original container before beginning.
NOTE: Older containers of stain and paint may need to be
strained before use.
Remove the battery pack from the sprayer.
Remove the quick-lock container by twisting counter-
clockwise so that the arrow on the container lines up
with the "unlock" symbol on the lid.
Fill the container with paint or stain as desired. Do not
fill above the max fill mark on the container.
Reinstall the container on the sprayer and twist
clockwise so that the arrow on the container lines up
with the "lock" symbol on the lid.
SELECTING THE PROPER SPRAY Trap
See Figure 5, page iL
Use the round tip for latex paints, oil-based paints,
and stains. This tip sprays in a round pattern.
To
Use the wide fan tip for latex paints. This tip
sprays in a wide pattern that can be adjusted from
horizontal to vertical.
switch tips:
Remove the battery pack from the sprayer.
Remove the installed tip by turning it counter-clockwise.
Install the desired tip and rotate clockwise to tighten
securely.
NOTE: The tip should be tightened securely by hand. A
too loose or overtightened tip may cause the sprayer to
leak or be damaged.
8 - English