230 V~
1 '
n
= 1450/min (disc)
0
50 Hz
375 W
1 '
V
= 275 m/min (belt)
0
English
GB
Product: Ferm Belt sander
Type BS-702, Article number 330702
Ferm, Genemuiden, The Netherlands
Sound pressure level L pa
80 dB(A)
SERIAL NUMBER
The serial number on the machine consists of the fol-
lowing elements.
Serial nr.
ORDER NUMBER/YEAR OF CONSTRUCTION
READ THIS MANUAL CAREFULLY BEFORE USING
THE BELT SANDER!
1. SPECIFIC SAFETY RULES
BEFORE USING THE MACHINE:
1. The following points need to be checked:
- Do the connecting voltage of the machine corre-
spond with the mains voltage;
- Are the mains lead and the mains plug in a good
condition; strong, without ravels or damages.
2. For functional reasons the turning parts of this machi-
ne are not covered. Therefore it is of utmost impor-
tance to be careful. Hold the workpiece firmly, to
prevent it from slipping from your hands. Never
touch the sanding surfaces of a working machine with
your hands.
3. Avoid the use of long extension cables.
4. If necessary, secure the sanding machine with screws.
BEFORE YOU OPERATE THE MACHINE:
1. Always keep the mains cable away from moving parts
of the machine;
2. Use safety goggles;
3. Use a dust mask.
2
150 mm
100 x 915 mm
IMMEDIATELY SWITCH OF THE MACHINE
IN CASE OF:
1. defective mains plug, mains line or damage to the
mains line;
2. defective switch;
3. smoke or bad smell caused by scorched isulation.
2. INSTALLATION
Avoid the use of long extension cables. If necessary, secu-
re the sanding machine on a working bench with help of
screws through the holes in the feet of the machine fra-
me. Do not forget to leave enough space around the ma-
chine for the workpieces to be sanded.
3. DESCRIPTION
This machine combines all the advantages of a horizontal
and a vertical belt sander with those of a disc sander. Its
sturdy construction in cast iron and steel makes the ma-
chine suitable for every sanding job.
4. BEFORE PUTTING THE MACHINE
INTO OPERATION
OPERATION (SEE FIG. 1)
1. Machine frame;
2. Motor;
3. Roller stop and parallel stop;
4. Clamping handle;
5. Transport roller;
6. Sanding belt;
8. Fence;
9. Drive roller;
10. Aluminium disc;
11. Sanding disc;
12. Work plate;
13. Mitre scale;
14. Supporting arm.
ASSEMBLY
-
Put the machine frame on its head and press the four
rubber stops into the foot of the frame.
-
Machine frame, aluminium disc (10) and work plate
(12) are supplied in separate packaging.
-
Push the aluminium disc on the shaft and fasten the
AVAILABLE SPARE PARTS FOR BS-702
REF.NR.
DESCRIPTION
4
BALL BEARING 6201 ZZ
5
DRIVE ROLLER
12
ADJUSTMENT BOLT
14
IDLER ROLLER
17
PLATE TABLE
21
DRIVE PULLEY
23
MOTOR
27
BASE PLATE
28
SWITCH
30
BAR
31
ADJUSTMENT BLOCK
32
MOTOR PULLEY
33
V-BELT M21
36
ALUMINIUM DISC
39
TABLE BRACKET
40
TABLE TILT TRUNION
41
MITRE BAR
42
KNOB/BOLT FOR MITRE BAR
46
TABLE
47
MITRE GAUGE
49
SHAFT FOR DRIVE ROLLER
51
SHAFT FOR IDLER ROLLER
52
BALL BEARING 6201 ZZ
56
INDICATOR
78
CAPACITOR (6 µF = 450 VAC)
77
RUBBER FOOT
Ferm
Ferm
FERM NR. BS-702
806201
402800
402801
402802
402803
402804
402805
402806
402807
402809
402810
402811
402812
402815
402816
402817
402818
402819
402820
402821
402822
402823
806201
402824
402825
402826
35