Download  Print this page

Layout2&system2(layout And System Setting Display 2); Analog Color Adj Analog Colour Adjustment Display - Mitsubishi Electric CP910E Operation Manual

Hide thumbs

Advertisement

ADJUSTMENTS & SETTINGS (SERVICE MENU)
Hi/Mid/Low
POINT(Hi/Mid/Low)
(EXAMPLE)
Pointing lighter colour much lighter;
Set the setting level for POINT(Hi) and Hi higher.
It takes time to set the gamma value by CPU. Wait until the normal display is shown
after pressing SET button.
It may take time to switch the program when the value of gamma setting is changed.
LAYOUT2&SYSTEM2 Layout and system setting display 2
PRN V AREA
Adjusts the vertical position of memory image.
Setting area -10 to 10 ( adjusts 2 lines each)
This menu is displayed only when IMAGES is set for 2 in L size paper.
PRN V AREA permits adjustment of the vertical position of the image so that the
clipped part of the image can be moved higher and lower.
SEPARATE
Selects whether a white frame is added to each print or not.
OFF
Prints without white frame. (A white frame appears according to the
setting of LAYOUT.)
ON
Prints with white frame.
MARGIN CUT
Cuts the margin of the printed paper.
This function is very convenient to stick the printed image on the card. The figure
shows S size print paper setting.
OFF
Margin is not cut.
ON
Margin is cut.
Only OFF is displayed when selecting THERMAL : ON.
CHECK EXIT
Selects whether this unit operates paper detecting function when
the printed paper is left at the print outlet or not.
OFF
Does not operate paper detecting function.
ON
Operates paper detecting function.
Only OFF is displayed when selecting THERMAL : ON.

ANALOG COLOR ADJ Analog colour adjustment display

This menu is used to adjust the image of analog input signal before storing in the
memory.
INPUT
Selects processing of video signal.
COLOR
Processes as colour video signal.
B&W
Processes as monochrome video signal. (The image is shown in
black and white.)
Select B&W when inputting monochrome signal.
BRT (Bright)
Adjust the brightness of the printing image.
CONT (Contrast)
Adjust the contrast of the printing image.
R-SUB
Adjusts red-subcontrast of the printing image. Red is added with
] and blue is added with [.
G-SUB
Adjusts green-subcontrast of the printing image. Green is added
with ] and pink is added with [.
B-SUB
Adjusts blue-subcontrast of the printing image. Blue is added with
] and yellow is added with [.
COLOR
Adjusts density of the printing image. The colour of the image gets
deeper with ] and lighter with [.
Adjusts the contour of image. The contour is reinforced with ] and
APT
softened with [.
Initializes each setting. When pressing ], the values of BRT,
CENTER
CONT, R-SUB, G-SUB, B-SUB, COLOR and APT will be reset to
centre value.
CANCEL
Cancels the change of ANALOG COLOR ADJ and resets to the
stored setting.
40
Adjusts the colour depth of image by selected point.
Selects the point to adjust the colour depth.
NOTE
LAYOUT2&SYSTEM2
PRN V AREA (L2 ONLY) 0 (±10)
SEPARATE
OFF/ON
MARGIN CUT
OFF/ON
CHECK EXIT
OFF/ON
A
Gray part is
cut when
MARGIN
CUT is ON.
ANALOG COLOR ADJ
INPUT
COLOR/B&W
BRT
: 0
CONT : 0
R-SUB : 0
C
R
G-SUB : 0
M
G
B-SUB : 0
Y
B
COLOR : 0
APT
: 0
CENTER
CANCEL

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric CP910E

Comments to this Manuals

Symbols: 0
Latest comments: