Rotate And Flip The Blades; Replace The Blades; Keep It Clean; Cleaning The Body - Worx Landroid WG797E Original Instructions Manual

dull and worn out, they should be replaced with the spare blades
provided with your Landroid
your nearest WORX retailer.
A. Rotate and Flip the Blades
®
Your Landroid L carries the Blades that are all screwed onto the Blade
Disc (16). The Blades allow the Landroid
and attention. Every once in awhile, you should simultaneously rotate
and flip all blades for a perfect cut. When rotating and flipping the
Blades, make sure all the Blades are adjusted at the same time or else
it could make the Blade Disc off balance. If your Landroid
a normal schedule (daily) then the Blades should last one season if
they are rotated and flipped every month. Always check to see if the
Blades are chipped or damaged and replace them if they are.
B. Replace the Blades (See Fig. L)
After some time, usually every season, your Landroid
mowing while using Blades of different age and quality. So when replacing the Blades, make sure to replace all of them
at the same time. You can replace them with one of the three spare Blade kits and extra Blade screws supplied with your
®
Landroid L.
Before attempting to replace your Landroid
steps:
1. Gently flip the Landroid
2. Remove the battery cover and remove the battery.
3. Take the screws off the Blades with a screwdriver
4. Firmly screw on the new Blades
5. Refit the battery and battery cover.
IMPORTANT: After screwing the Blade to the Blade Disc, make sure the Blade is able to spin freely.

7.2 Keep it Clean

WARNING! Before cleaning turn your Landroid
OFF by pressing the ON/OFF Button to OFF. Put on
protective gloves before cleaning the Blade Disc (16) and
do not use running water. (See Fig. M)
A. Cleaning the Body
®
Your Landroid L will live a much happier and longer life if it is cleaned
regularly. Although, as your Landroid
you will need to take care when cleaning, so DO NOT use a hose,
high pressure washers or otherwise pour running water on your
®
Landroid L, it is best to use a spray bottle filled with water. When
cleaning the machine body use a soft brush or clean cloth and avoid
using solvents or polishes (See Fig. M). Lastly, make sure that you
remove all build up of grass clippings and debris.
B. Cleaning the Underside
Again, it is important that you power the Landroid
touching the Blade Disc (16).
First, flip your Landroid
and the Front (18) and Drive Wheels (11). Clean everything thoroughly with a soft brush or moist rag cloth.
Rotate the Blade Disc to ensure it rotates freely. Check the blades spin freely around the fixing screws. Remove any
obstructions.
IMPORTANT: Remove any lodged debris so that it does not cause a crack in the Blade Disc. Even the
tiniest crack can decrease your Landroid
C. Clean the contact pins and the charging strips
Clean the Contact Pins (2) located on the Charging Base (3) and the Charging Strip (5) located on the Landroid
cloth. Remove any build up of grass clippings and debris around the contact pins and charge strips periodically to ensure
®
the Landroid L successfully charges each time.
Lawn Mowing Robot
®
L. Spare blades are also available at
®
L to do its job and need care
®
Ls Blades, turn the power off and put on protective gloves. Then follow these
®
L over
®
L is an electric machine,
®
L OFF using the ON/Off Button and wear protective gloves before
®
L upside down to expose its underside. Here you will see the Blade Disc the Main Housing (14),
®
L mowing output.
®
L mows on
L
®
Ls Blades will need to be replaced. Your Landroid
®
L
M
®
L does not like
®
L using a
EN
13