In Multeq Mode; Adjusting Sound Setting In Manual Mode; Turning Subwoofer On/Off; Setting The Subwoofer Phase - Alpine cda-9886 Quick Reference Manual

Adjusting Subwoofer LevellBass Level/
Treble Level/Fader (Between Front and
Rear)lBalance (Between Left and Right)/
Black Out in MultEQ mode
You can change these settings to create your own preference in MultEQ
(Curve I or Curve 2) mode.
1
Press
IMPRINT
to activate the MultEQ adjustment
mode.
2
Turn the
Rotary encoder
to select the desired Item,
and then press
<\IENT.
SUBW Level,J
H
Bass Level
H
Treble Level
H
Fader'z
H
Balance
H
Black Out,3
H
SUBW Level
3
Turn the
Rotary encoder
to change the setting as
below, and then press
<\ lENT.
Subwoofer level:
a -
+
15
Bass level: -7 -+ 7
Treble level: -7-+7
Fader: A15 - F15
Balance: 115 - A15
Black Out: ON/OFF
• If no operation is performed for
60
seconds after selecting the
SUBW. Level, Bass Level. Treble Level. Fader. Balance or Black Out
mode. the unit automatically returns to normal mode.
,J
When the subwoofer mode is set to OFF, its level cannot be adjusted.
and the subwoofer ON/OFF cannot be adjusted in MultEQ (Curve I
or Curve
2)
mode.
,.] If you set the 2.2ch (3WAY)/4.2ch (FRONT/REARlSUBW.) switch of
the Imprint-Box (PXA-HIOO) to 2.2ch (3WAY). you cannot adjust the
FADER mode. For details. refer
10
the Owner's Manual of
PXA-HIOO.
,3
When Blackout mode is turned on. all display indications on this unit
will tum off to reduce power consumption. This additional power
enhances the sound quality.
If any button on the unit is pressed during the blackout mode. the
function will be displayed for 5 seconds to show the operation before
returning to Blackollt mode.
• Depending on the connected devices. some functions and display
indications do not work.
Adjusting Sound Setting in Manual Mode
You can change these sound settings to create your own preference
when the MultEQ mode is set to MultEQ off (Manual Mode).
Use steps 1 to 4 to select one of the Sound menu
modes to modify.
see
the applicable section below for
details about the selected Item.
1
Press
IMPRINT
to activate the Sound menu
selection mode.
30-EN
2
Turn the
Rotary encoder
to select the desired Item,
and then press
<\IENT.
Subwoofer
H
SUBW System'}
H
SUBW Phase'}
H
SUBW Channel'}
H
Factory's EO
H
TW Setup,.]
H
Filter Type
H
Media Xpander
H
MX Level
03
H
EO Mode
H
TCA Parameter
H
Sound Field,.4
H
Black Out
H
Subwoofer
(e.g. Select SUbwoofer)
,} These functions are inoperable when Subwoofer is set to OFF.
,.] Thisfunction can be operable only when PXA-HIOO (sold
separately) is connected and 2.2ch (3WAY) mode is set. For details.
refer to the Owner's Manual of PXA-HIOO.
03 This function is inoperable when Media Xpander is set to OFF.
,.4
In step 2, three sound adjustment items (Parametric EQlGraphic EQ,
T.Correction, X-Over) can be selected in Sound Field Adjustment
mode, tum the Rotary encoder to select the desired item, and then
press <\IENT to continue
10
step 3.
3
Turn the
Rotary encoder
to change the setting,
and then press <\IENT.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold
~IESC
for at least 2 seconds to
return to normal mode.
• Media Xpander. Factory's EQ. Parametric EQlGraphic EQ
Adjustment. EQ Mode and MX Level Adjustment are inoperable
when Defeat is set to ON.
• Pressing
~IESC
returns
10
the previous Sound menu mode.
• Ifno operation is performedfor
60
seconds. Sound menu mode is
canceled.
When the subwoofer is on, you can adjust the subwoofer output level
(referto page 14).
OFF
H
ON (Initial setting)
When the subwoofer is on, you can select either System I or System2
for the desired subwoofer effect.
1 (Initial setting)
H
2
System 1: Subwoofer level changes according to the main
volume setting.
System 2: Subwoofer level change is different from the main
volume setting. For example. even at low volume
settings, the subwoofer is still audible.
PHASE 00 (Initial setting)
H
PHASE 180 0
The subwoofer output phase is toggled SUBWOOFER NORMAL (00)
or SUBWOOFER REVERSE (180 0
).
To adjust the level, tum the
Rotary encoder.
Adjusting Subwoofer LevellBass Level/
Treble Level/Fader (Between Front and
Rear)lBalance (Between Left and Right)/
Black Out in MultEQ mode
You can change these settings to create your own preference in MultEQ
(Curve I or Curve 2) mode.
1
Press
IMPRINT
to activate the MultEQ adjustment
mode.
2
Turn the
Rotary encoder
to select the desired Item,
and then press
<\IENT.
SUBW Level,J
H
Bass Level
H
Treble Level
H
Fader'z
H
Balance
H
Black Out,3
H
SUBW Level
3
Turn the
Rotary encoder
to change the setting as
below, and then press
<\ lENT.
Subwoofer level:
a -
+
15
Bass level: -7 -+ 7
Treble level: -7-+7
Fader: A15 - F15
Balance: 115 - A15
Black Out: ON/OFF
• If no operation is performed for
60
seconds after selecting the
SUBW. Level, Bass Level. Treble Level. Fader. Balance or Black Out
mode. the unit automatically returns to normal mode.
,J
When the subwoofer mode is set to OFF, its level cannot be adjusted.
and the subwoofer ON/OFF cannot be adjusted in MultEQ (Curve I
or Curve
2)
mode.
,.] If you set the 2.2ch (3WAY)/4.2ch (FRONT/REARlSUBW.) switch of
the Imprint-Box (PXA-HIOO) to 2.2ch (3WAY). you cannot adjust the
FADER mode. For details. refer
10
the Owner's Manual of
PXA-HIOO.
,3
When Blackout mode is turned on. all display indications on this unit
will tum off to reduce power consumption. This additional power
enhances the sound quality.
If any button on the unit is pressed during the blackout mode. the
function will be displayed for 5 seconds to show the operation before
returning to Blackollt mode.
• Depending on the connected devices. some functions and display
indications do not work.
Adjusting Sound Setting in Manual Mode
You can change these sound settings to create your own preference
when the MultEQ mode is set to MultEQ off (Manual Mode).
Use steps 1 to 4 to select one of the Sound menu
modes to modify.
see
the applicable section below for
details about the selected Item.
1
Press
IMPRINT
to activate the Sound menu
selection mode.
30-EN
2
Turn the
Rotary encoder
to select the desired Item,
and then press
<\IENT.
Subwoofer
H
SUBW System'}
H
SUBW Phase'}
H
SUBW Channel'}
H
Factory's EO
H
TW Setup,.]
H
Filter Type
H
Media Xpander
H
MX Level
03
H
EO Mode
H
TCA Parameter
H
Sound Field,.4
H
Black Out
H
Subwoofer
(e.g. Select SUbwoofer)
,} These functions are inoperable when Subwoofer is set to OFF.
,.] Thisfunction can be operable only when PXA-HIOO (sold
separately) is connected and 2.2ch (3WAY) mode is set. For details.
refer to the Owner's Manual of PXA-HIOO.
03 This function is inoperable when Media Xpander is set to OFF.
,.4
In step 2, three sound adjustment items (Parametric EQlGraphic EQ,
T.Correction, X-Over) can be selected in Sound Field Adjustment
mode, tum the Rotary encoder to select the desired item, and then
press <\IENT to continue
10
step 3.
3
Turn the
Rotary encoder
to change the setting,
and then press <\IENT.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold
~IESC
for at least 2 seconds to
return to normal mode.
• Media Xpander. Factory's EQ. Parametric EQlGraphic EQ
Adjustment. EQ Mode and MX Level Adjustment are inoperable
when Defeat is set to ON.
• Pressing
~IESC
returns
10
the previous Sound menu mode.
• Ifno operation is performedfor
60
seconds. Sound menu mode is
canceled.
When the subwoofer is on, you can adjust the subwoofer output level
(referto page 14).
OFF
H
ON (Initial setting)
When the subwoofer is on, you can select either System I or System2
for the desired subwoofer effect.
1 (Initial setting)
H
2
System 1: Subwoofer level changes according to the main
volume setting.
System 2: Subwoofer level change is different from the main
volume setting. For example. even at low volume
settings, the subwoofer is still audible.
PHASE 00 (Initial setting)
H
PHASE 180 0
The subwoofer output phase is toggled SUBWOOFER NORMAL (00)
or SUBWOOFER REVERSE (180 0
).
To adjust the level, tum the
Rotary encoder.