Imprint Operation (Optional); Changing Multeq Mode - Alpine CDA-9886 Quick Reference Manual

IMPRINT Operation
(Optional)
Adjusting Subwoofer Level/Bass Level/
Treble Level/Fader (Between Front and
Rear)/Balance (Between Left and Right)
in MullEQ mode
- Depending on the connected devices. some functions and display
indications do not work.
• If
//0
operation is peiformedfor 60 seconds after selecting the
SUBW LEVEL. BASS LEVEL, TREBLE LEVEL. FADER or
BALANCE mode the IIIrit automatically returns to normal mode.
,I
When tire SUB WOOFER mode is set to OFF.
irs
level cannm be
adjusted, and the SUB WOOFER ON/OFF cannot be adjusted in
MultEQ (CURVE I or CURVE 2) mode.
,2
If you set tire 2.2ch (3WAY)/4.2ch (FRONT/REARJSUBW) switch of
the Imprint-Box (PXA-H 100)
10
2.2cit (3WAY), you cannot adjust the
FADER mode. For details, refer to tite Owner's Manual of PXA-
HI 00.
You can change these settings to create your own preference in MultEQ
(CURVE I or CURVE 2) mode.
1
Press IMPRINT to activate the MultEQ adjustment
mode.
2
Turn the Rotary encoder to select the desired item,
and then press
~/ENT.
SUBW LEVEL-I H BASS LEVEL
H
TREBLE LEVEL
H
FADER,2
H
BALANCE
H
SUBW LEVEL
3
Turn the Rotary encoder to change the setting as
below, and then press
~/ENT.
Subwoofer level:
a -
+ 15
Bass level: -7-+7
Treble level: -7-+7
Fader: R15 - F15
Balance: L15 - R15
~/ENT
/·~r
=:J
IESC Preset buttons IMPRINT
(1 through 6)
Rotary encoder
I
BAND
b~:,
~,_.'
I
SOURCEI<!>
MultEQ. developed by Audyssey Labs. automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this. MultEQ must take
measurements ofthe vehicles response characteristics. For details on the
set up procedure. consult your authorized Alpine dealer.
Changing MultEQ mode
Alpine introduces IMPRINT - the world's tirst technology that
thoroughly eliminates in-car acoustic problems that normally degrade
sound quality, which enables us to experience music the way the artist
intended. refer to "About IMPRINT" (page 33),
When the IMPRINT-BOX (PXA-H 100) (sold separately) is connected
to this unit, MultEQ and the following sound adjustment can be
performed.
Press and hold IMPRINT for at least 2 seconds to
change MultEQ mode.
MULTEO OFF (Manual Mode) ~ CURVE 1 (MuItEO-1) ~
CURVE 2 (MuItEO-2)
~
MULTEO OFF (Manual Mode)
• The Curve mode can be selected onlv when curve I and curve 2 are
stored.
• When using MultEQ, MEDIAXPANDER. MX LEV MODE,
CROSSOVER. T.CORR PARA. FACTORY'S EQ. SUBW PHASE.
SUBW CHANNEL. TW SETUP. EQ MODE. FILTER TYPE and
PARAMETER EQ/GRAPHIC EQ are set autolllaticali. They are
//0
longer user adjustable.
- Wlren an extel'l1al audio pl1Jcessor is connected. the MultEQfunction
cannot be used.
26-EN
IMPRINT Operation
(Optional)
Adjusting Subwoofer Level/Bass Level/
Treble Level/Fader (Between Front and
Rear)/Balance (Between Left and Right)
in MullEQ mode
- Depending on the connected devices. some Junctions and display
indications do not work.
• IJ
//0
operation is peiformedJor 60 seconds aJter selecting the
SUBW LEVEL. BASS LEVEL, TREBLE LEVEL. FADER or
BALANCE mode the IIIrit automatically returns to normal mode.
,I
When tire SUB WOOFER mode is set to OFF.
irs
level cannm be
adjusted, and the SUB WOOFER ON/OFF cannot be adjusted in
MultEQ (CURVE I or CURVE 2) mode.
,2
IJyou set tire 2.2ch (3WAY)/4.2ch (FRONT/REARJSUBW) switch oj
the Imprint-Box (PXA-H 100)
10
2.2cit (3WAY), you cannot adjust the
FADER mode. For details, reJer to tite Owner's Manual oj PXA-
HI
00.
You can change these settings to create your own preference in MultEQ
(CURVE I or CURVE 2) mode.
1
Press IMPRINT to activate the MultEQ adjustment
mode.
2
Turn the Rotary encoder to select the desired item,
and then press
~/ENT.
SUBW LEVEL-I H BASS LEVEL
H
TREBLE LEVEL
H
FADER,2
H
BALANCE
H
SUBW LEVEL
3
Turn the Rotary encoder to change the setting as
below, and then press
~/ENT.
Subwoofer level:
a -
+ 15
Bass level: -7-+7
Treble level: -7-+7
Fader: R15 - F15
Balance: L15 - R15
~/ENT
/·~r
=:J
IESC Preset buttons IMPRINT
(1 through 6)
Rotary encoder
I
BAND
b~:,
~,_.'
I
SOURCEI<!>
MultEQ. developed by Audyssey Labs. automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this. MultEQ must take
measurements ofthe vehicles response characteristics. For details on the
set up procedure. consult your authorized Alpine dealer.
Changing MultEQ mode
Alpine introduces IMPRINT - the world's tirst technology that
thoroughly eliminates in-car acoustic problems that normally degrade
sound quality, which enables us to experience music the way the artist
intended. refer to "About IMPRINT" (page 33),
When the IMPRINT-BOX (PXA-H 100) (sold separately) is connected
to this unit, MultEQ and the following sound adjustment can be
performed.
Press and hold IMPRINT for at least 2 seconds to
change MultEQ mode.
MULTEO OFF (Manual Mode) ~ CURVE 1 (MuItEO-1) ~
CURVE 2 (MuItEO-2)
~
MULTEO OFF (Manual Mode)
• The Curve mode can be selected onlv when curve I and curve 2 are
stored.
• When using MultEQ, MEDIAXPANDER. MX LEV MODE,
CROSSOVER. T.CORR PARA. FACTORY'S EQ. SUBW PHASE.
SUBW CHANNEL. TW SETUP. EQ MODE. FILTER TYPE and
PARAMETER EQ/GRAPHIC EQ are set autolllaticali. They are
//0
longer user adjustable.
- Wlren an extel'l1al audio pl1Jcessor is connected. the MultEQJunction
cannot be used.
26-EN